Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
sunlight, heating pipes, furnaces, etc. Do not store where temperatures go below
+40 F or above +120 F.
CHARGING – It is recommended that the Clip&Shear™ is always stored in its
charging rack with the charger plugged in. The unit's charger is designed to pro-
vide a trickle charge that will properly maintain and not harm the battery. If you
wish to store the unit in the off-season not using its charger, you should charge the
unit for 20 hours before storage. .
PREVENTING CORROSION – Fertilizers and other garden chemicals contain
compounds that greatly accelerate the corrosion of metals. Do not store the appli-
ance on or adjacent to fertilizers or chemicals. Prior to storage and before or after
each use, clean and oil blades as described in this manual.
ACCESSORIES
Extension Handle Kit is available.
Note: Accessories are sold separately. Only use American Gardner approved
accessories with the Clip&Shear™. The use of non-approved accessories could be
hazardous and will void the warranty.
BATTERY RECYCLING – To preserve natural resources, please recycle or dis-
pose of this product's NICKEL-CADMIUM (NiCd) BATTERY properly. Local, state
and federal laws prohibit disposal of NiCd batteries in ordinary trash. American
Gardener is a participant in the Rechargeable Battery Recycling Corporation
(RBRC) recycling program. We have paid a fee to allow for these batteries to be
properly disposed of via a RBRC collection site (various retailers are also RBRC
participants). Please call the RBRC toll free number of (800) 822-8837 or visit the
RBRC web site of
www.rbrc.com
to find a battery collection center near you.
BATTERY REPLACEMENT – You may order batteries directly from American Gar-
dener by calling (800) 637-2867.
BLADE REPLACEMENT – You may order blade packs directly from your retailer or
American Gardener by calling (800) 637-2867.
WARNING:
When replacing the batteries, the proper polarity or direction must be
observed. Be careful to follow installation instructions that are shipped with the
replacement batteries to avoid damage and personal injury.
SERVICE:
Two Year Warranty on American Gardener Clip&Shear
All manuals and user guides at all-guides.com
Figure-3
®
7
During normal residential use, if this Clip&Shear fails due to a defect in material or
workmanship within two years from the date of purchase, American Gardener, at its
sole discretion, will repair or replace the unit free of charge.
For warranty services or questions please call (800) 637-2867.
This warranty applies only while this Clip&Shear is used in the United States.
The warranty does not cover components that are subject to normal wear, such as
the blades and batteries. It also does not cover abuse, misuse, or use of the prod-
uct in a commercial setting. Replacement parts are available for purchase from the
retailer you bought your product from, or by calling us at (800) 637-2867 or visiting
our web site at www.american-gardener.com.
Please read and follow the instructions for this product carefully.
This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.
If you see any condition that may affect safe operation, or you have any questions,
contact our customer service number at: 1-800- 637-2867.
TROUBLE SHOOTING
Problem: Unit will not charge properly.
Solution(s):
•
Inspect charge connectors on unit and charge rack to insure a proper connec-
tion.
•
Many outdoor or garage outlets in newer homes are protected by ground fault
(GFCI) circuits to prevent against electrical shock from moisture. Make sure
the charger is completely plugged into wall outlet and that the outlet is in work-
ing condition (i.e. not temporarily disabled by a GFCI protector).
•
Remove blade pack per instructions in Figure 2. Slide back the battery door
and inspect that the battery pack is properly connected.
Problem: Cutting or run-time performance is diminished.
Solution(s):
•
Please follow the trimming techniques described in this manual for best per-
formance.
•
Inspect blades to make sure they are clean, free of obstruction(s) and well lu-
bricated. Refer to Maintenance section of manual on cleaning and lubricating
blades.
•
Make sure the unit is fully charged – see the Operations section of this manual
for charging details.
Problem: Thumb safety switch is difficult to hold on during use
Solution:
•
The thumb safety switch need only be engaged when starting the unit. There
is no need to keep switch in forward position while using the product.
8
Publicidad
Tabla de contenido
