Panlux VANA S Instrucciones página 3

INSTRUCTIONS
MODEL:
SV150/B
SV150/C
SV500/B
SV500/C
Before using or installing the product, kindly read the instructions and follow safety rules. Installation should
be provided by qualified person or company.
Thank you for choosing the item of company PANLUX s.r.o.
Technical data
Power supply: 230V~50Hz
Input fuse: 6,3A/250V
Supply in standby mode: <1W
Additional load: max. 850W (SV150) | 500W (SV500)
incandescent lamp
max. 250W (SV150) | 150W (SV500)
fluorescent lamp
Lampholder: R7s
Protection class: I.
IP Protection: IP44
Angle of detection: horizontal – 180°, vertical – 60°
Rotation of sensors head: horizontal - ±90°,
vertical - ±90°
Reach: max. 12m (SENS), adjustable
Time setting: 10s (±5s) to 4min (±1min) (TIME),
adjustable
Twilight setting: 2-2000lx (LUX), adjustable
Recommended installation height: 2,5m
Terminal block: 3x1,5mm²
Operating temperature: -5~45°C
Location: interiors, exteriors
Material: metal, plastic ABS
Installation
SV150 max. 150W R7s/78mm 130x130x225mm 600g
SV500 max. 500W R7s/118mm 200x190x285mm 1030g
26mm 26mm
35mm 35mm
225mm
285mm
ø5mm | 8mm
130mm 130mm
52mm | 69mm
200mm 190mm
104mm | 138mm
Notice
Before using, check the product and make sure there is no damage,
otherwise do not use it.
Before every manipulation assure that mains electrical supply
is disconnected.
In case of damage do not repair or disassemble the product.
For the best functional results, move toward the sensor (see to pic. 6).
The incorrect function of the product can be caused by interruption
of electromagnetic field, small temperature difference between
moving object and surroundings, reflection (e.g. strong luminous
source).
Before replacing the light source switch off the light and let it cool
down.
Kindly use only recommended light sources (SV150 – max.150W
R7s/78mm, SV500 – max.500W R7s/118mm)
Infringement of any mentioned instruction can cause harm to health
or property.
2
1
230V~50Hz
ø8mm | 10mm
cable gland
Principle of PIR sensor
PIR sensor receives infra-red waves emitted by objects in reach radius. With movement in the detection area sensor notices
the change and initiates trigger order „Light on" for adjusted time.
Reach setting (sensitivity) – SENS (max. 12m)
Reach is to be understood as the area traced out by angle of detection and min. to max. available distance from sensor.
Reach can be changed by knob or with rotation of sensors head.
Time setting (switch-off delay) – TIME (10s (±5s) to 4min (±1min))
The countdown of adjusted time begins after last detected movement. We recommend setting the function on minimum
during functional test.
Twilight setting (response threshold) – LUX (2 – 2000lx)
We recommend setting the function on maximum during test.
Stated information may differ according to position and installation height.
Position marked - or  applies to minimum and position marked
If the product is mechanically damaged or connected unprofessionally, guarantee cannot be allowed.
3 4
L N
terminal block
VANA S
Industrial lamp with PIR sensor
or applies to maximum.
+
5 6
180˚
60˚
12m
0,5 - 3,5m
1,8 - 2,5m
min. 50mm
min. 200mm
min. 90°
max. 50°
All right reserved. Technical data can be changed without previous notice.
7
max. 4°
max. 4°
min. 1m
UM_VANAS_110915