Special Buttons; Auto-Search Programming - Rotel RR-939B Manual De Instrucciones

RR-939B
There are five MACRO buttons on the RR-939B – the four
buttons labeled M1, M2, M3, and M4, along with the
POWER button. A sequence of up to eight different com-
mands can be memorized to be replayed automatically
with the press of a MACRO button. See the section, PRO-
GRAMMING MACROS, for more detailed information.
Note: Macro buttons are available only in the AUD, SAT,
and CBL modes. However, you can include switching to a
different DEVICE mode as part of a macro, in order to op-
erate other components.
To replay a MACRO, first activate one of the DEVICE
modes (AUD, SAT, and CBL only). Then, press the desired
MACRO button. If a macro has been programmed for that
button, the RR-939B will replay the memorized sequence
of commands and the DEVICE button will blink red for
each command. If no macro has been programmed, or if
macros are not available in that DEVICE mode, nothing
will happen and no DEVICE buttons will blink.

Special Buttons

4
There are two special function buttons at the bottom of
the RR-939B remote.
The LIGHT button turns on backlighting so you can see
the buttons in a dark room. The lights stay on for 7 sec-
onds and will stay on for an additional 7 seconds each
time another button is pressed.
The SHIFT button activates additional commands for
some buttons. These functions are shown in italics on
the illustrations and in the command tables. To activate
one of these commands, press and release the SHIFT
button and then press the desired COMMAND button.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Programming
The RR-939B can replace up to eight different remote
controls, one for each of the eight DEVICE buttons. Be-
fore you use it, you must program the RR-939B, i.e. tell it
which audio/video components you wish it to control.
The RR-939B contains hundreds of command sets for
various A/V components. Programming the remote in-
volves selecting the command sets that correspond to
the components in your system, and assigning them to
the eight DEVICE buttons by entering a three digit code.
This need only be done once during initial set-up of the
RR-939B.
5
All manuals and user guides at all-guides.com
The easiest way to proceed is to find your components
and corresponding three-digit codes from the list of
codes supplied with this manual. If your component is
not listed, there is an alternative auto-search method for
finding the right command set.
Three Digit Code Programming
Find your audio/video component in the code list and
note the 3-digit code(s):
Step One: Turn on the component you wish to memorize.
Step Two: Press the corresponding DEVICE button (for
example, if you are memorizing the command set for a
CD player, press the CD DEVICE button at the top of the
RR-939B). While pressing the DEVICE button, simulta-
neously press the MUTE button and hold both for at least
one second. The DEVICE key will light in red for 20 sec-
onds, indicating that you have entered the program
mode. The next step must be done within this 20 second
period, or the RR-939B will revert to its standard operat-
ing mode.
Step Three: Point the RR-939B at the audio/video compo-
nent and enter the 3-digit code, using the numeric but-
tons. The DEVICE key will flash each time you enter a
digit. If you have entered the correct code, the compo-
nent will turn off. If there is more than one 3-digit code
for your brand of source component, continue entering
additional 3-digit codes from the list until the component
turns off, indicating that you have found the right one.
Step Four: Store the code number by pressing the corre-
sponding DEVICE button again. The button will blink
twice to confirm the storage of the code in memory.
Step Five: Test the COMMAND buttons, using the tables
as a reference for the available functions. If the functions
do not work correctly, repeat the above steps, with the
next available 3-digit code from the list for your brand of
component.
Repeat the steps above for each of up to eight compo-
nents, assigning each one to the appropriate DEVICE key.

Auto-Search Programming

If the code table does not provide a 3-digit code or if
none of the code numbers assigned to your brand of
component work, use the following auto-search method
to find a code number that will operate your components.
English
6