Installation - Flott PBS 150 ST Instrucciones Para El Uso Y Manutencion

- Wear suitable clothes, without wide sleeves or articles such
as scarves, chains and bracelets which could get caught
in the moving parts.
- Always use personal protection devices: protective goggles
as recommended by safety standards, gloves of the right
size, headphones or earplugs, and hairnets if necessary.
- Use the tools recommended in this manual if you want
to achieve the best performance from your sawing
machine.
- Any power cable extensions must be type approved and
comply with safety standards.
- Avoid using the machine if your psycho-physical condition
are precarious or upset.
1.6 SAFETY PROCEDURS FOR FURTHER RISK
- Always keep processing residues away from the cutting
area.
- Always use the clamp. The parts to be cut must always be
held fi rmly in the clamp.
- Always keep hands away from the working areas while the
machine is moving: before loading or unloading the part,
release the run button on the hand grip.
- Do not force the machine unnecessarily : excessive
cutting pressure could cause rapid wear to the blade and
negatively infl uence the performance of the machine in
terms of fi nishes and cutting precision.
1.7 INFORMATION REGARDING NOISE AND
VIBRATIONS
Noise
Noise level at the operator's work
position (without load) .............................. Leq 81.5 dB (A)
Noise level at the operator's work position (with load)
Cutting of 80 mm dia. barstock in 9SMnPb28 steel at speed
of 80 m/min ................................................ Leq 82.4 dB(A)
Cutting of 60x60 steel profi le with 3 mm wall thickness at
speed of 80 m/min. .................................... Leq 85.6 dB(A)
Test conditions
Sound power (without load) ......................Lwa 93.4 dB (A)
Sound power (with load)
Cutting of 80 mm dia. barstock in 9SMnPb28 steel at speed
of 80 m/min .............................................Lwa 94.2 dB (A)
Cutting of 60x60 steel profi le with 3 mm wall thickness at
speed of 80 m/min. ...................................Lwa 96.7 dB (A)
The measurements were carried out in accordance with
standard UNI EN ISO 3746.
Vibration
Mean frequency-weighted hand - arm acceleration vibration
exposure does not exceed 2.5 m/s².
The measurements were carried out in accordance with
standards UNI EN ISO 5349-1 and 5349-2.
The emission levels indicated are not necessarily safety
levels. Although there is a relationship between the emissions
and exposure levels, the values shown cannot be used for
establishing the need for further precautions. There are other
factors which infl uence the exposure levels of operators, such
as the features of the work place, presence of other sources
of noise, number of machines running, etc.
The exposure levels may also vary between countries.
This information is necessary for the user for better evaluation
of the risks and hazards deriving from noise.
NOTE: Personal hearing protection should be
used, such as headphones or earplugs.
8
1.8 INFORMATION ABOUT THE
ELECTROMAGNETIC COMPATIBILITY
The European regulations on safety and, in particular, the
Directive 2004/108/CE contemplate that all the equipment be
equipped with shielding devices against radio interferences
both from and towards the outside.
This machine is equipped with fi lters through which the
machine is safe and in compliance with above regulations.
Tests were carried out according to 61000-6-1, EN 61000-
6-3, EN 55014-1, EN 55014-2 regulations.
1.9 DESCRIPTION OF THE MACHINE (Fig. 1)
The belt sawing machine consists of two basic parts: the
machine body 5 complete with motor and drive 7 which is
integrated into lower part, consisting of the clamp 11, the
base 13 and swivel support 9.
Here is a list of the main parts with the number indicating it
in the drawing.
Legend Fig. 1
1 Grip
2 Blade tension handwheel
3 Vice speed-slide drive
4 Sliding blade guide
5 Machine body
6 Blade
7 Motor
8 Control box
9 Bar stop
10 Clamp (vice)
11 Morsa
12 Clamp drive
13 Base
14 Handle for handling
WEIGHT .................................................................. 35 Kg.
SIZE ........................................................ cm 108 x75xH80
.........................................in maximum overall dimensions.
PACKAGING SIZE ............................. cm 100 x 39 x H57
2

INSTALLATION

2.1 REMOVING THE PACKING
Remove the wooden frame which protects the machine
during transit.
Try not to damage the frame as you may have to move the
machine long distances or store it for long periods.
2.2 HANDLING (Fig. 2)
As the machine is considerably heavy (35 kg net), it needs
at least 2 people to lift it, positioned on either side.
The machine must be lifted and transported by the handle
14 fi xed on the base plate.
2.3 TRANSPORT (Fig. 2)
Before moving the machine from one place to another by
lifting it, apply the two handles 14 attached to the base.
Take the handles and fi x them with the screws and the nuts
on both sides of the base of machine.
It is necessary to low the saw body till the lower position and
fi x it to the base; then you can proceed with the trasport by
lifting the machine by two person moving it at the handle.
Should the machine be fi xed on a base plate (column) unlock
the screws fi rst.