Tabla de contenido
Publicidad
TRANSLATION OF THE ORIGINAL
INSTRUCTION MANUAL
BATTERY MIXER
CAUTION: BEFORE USING THE POWER TOOL, READ THIS
MANUAL
CAREFULLY
REFERENCE.
DETAILED SAFETY REGULATIONS
a) Use the tool with the optional handles supplied with the tool.
Loss of control can cause personal injury to the operator.
b) When carrying out work where the working tool could come
into contact with hidden electric cables, hold the power tool by
the insulated surfaces of the handle. Contact with a mains lead
can transfer voltage to the metal parts of the equipment, which could
result in an electric shock.
c) Avoid touching rotating parts. Touching rotating power tool parts,
especially accessories, may result in injury.
d) Wait for the power tool to stop before you lay it down. The
accessory tool may jam and result in loss of control of the power
tool.
e) If the accessory tool jams, switch off the power tool immediately,
be prepared for high reaction torques.
f) The mixer must not be used in an environment with a
potentially explosive atmosphere. Do not mix solvents or
substances containing solvents with a flash point below 210°C.
g) The agitator should always be started and stopped when the
agitator is submerged in the tank.
h) Always make sure the mixing tank is properly secured.
i) Do not put your hands or any objects into the tank during the
mixing operation.
WARNING! The device is designed to work indoors. Despite
the inherently safe construction, the use of safety measures
and additional protective measures, there is always a residual
risk of injury during work.
Explanation of the pictograms used
1. Read the operating manual, observe the warnings and safety
conditions contained in it!
2. Remove the battery from the device before making any
adjustments or cleaning.
3. Use personal protective equipment (safety goggles, hearing
protection, dust mask).
4. Use safety shoes.
5. Use protective clothing.
6. Protect the device against moisture.
7. Keep children away from the tool.
CONSTRUCTION AND APPLICATION
The mixer is a battery powered power tool. The drive is a brushless
DC motor. The battery mixer is an electric tool designed to work
both in construction and in other fields. The possibility of using
various mixing tools, adapted to the substances to be mixed, allows
the mixing of cement, plaster, floor coverings, paints, ordinary
plasters, self-leveling mortars and various chemicals.
WARNING! Do not use the power tool for purposes other than
those for which it was intended.
DESCRIPTION OF THE GRAPHIC PAGES
The numbering below refers to the components of the device shown
on the graphic pages of this manual.
58G084
AND
KEEP
IT
FOR
1. Mixer spindle
2. Gear selector
3. Switch
4. Switch lock button
5. Agitator shaft
6. Agitator
FUTURE
7. Speed control knob
* There may be differences between the drawing and the product.
EQUIPMENT AND ACCESSORIES
1. Agitator pin - 1 pc.
2. Stirrer - 1 pc.
3. Flat wrench - 2 pcs.
ASSEMBLY OF THE MIXER
• Screw the agitator shaft (5) into the agitator spindle (1) using the
supplied wrenches (fig. A).
• Screw the agitator (6) into the shaft (5).
ON / OFF
WARNING! Make sure the battery is fully charged before
starting work.
WARNING! When starting the mixer, hold the mixer with both
hands, as the motor torque may cause uncontrolled rotation of
the power tool.
It should be remembered that after switching off the mixer, its
moving parts continue to rotate for some time.
The mixer is equipped with a switch to prevent accidental start-up.
Turning on
• Press the switch lock button (4) located on the handle (fig. B).
• Press the switch button (3).
• Release the pressure on the switch lock button (4).
Turning off
• Release the pressure on the switch button (3).
2-SPEED SWITCH
The speed can be changed with the two-position gear selector
switch (2) (fig. C). Depending on the work to be performed, set the
gear selector to the correct position.
• Position "1" provides slower speed and more torque.
• Turn clockwise to position "2" for higher speed, less torque.
• To return to a lower speed, turn the switch to the left.
WARNING! Never move the gearshift switch while the mixer is
running. This could damage the power tool. If the switch
cannot be moved, turn the spindle slightly.
SPEED ADJUSTMENT
There is a speed control knob (7) on the mixer handle (fig. D). The
speed adjustment range is from 1 to 6, the speed can be changed
in individual gears depending on the user's needs.
MIXER OPERATION
• Always hold the mixer firmly (with both hands) during operation.
• Electronic regulator enables slow, spatter-free start and end of
mixing.
• By turning the regulator knob (7) it is possible to increase or
decrease the spindle speed.
WARNING! Before performing any installation, adjustment,
repair or maintenance activities, remove the battery from the
device.
MAINTENANCE AND STORAGE
• It is recommended to clean the device immediately after each use.
• Do not use water or other liquids for cleaning.
7
PREPARATION TO WORK
OPERATION / SETTINGS
CARE AND MAINTENANCE
Publicidad
Tabla de contenido
