Tabla de contenido
Publicidad
1
L
IMPORTANT
Please read
these
instructions carefully before you start to assemble this product.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these
instructions
in
a
safe
place
for future
reference.
»
Care &
Safety Advice
Please
follow
the instructions
as
listed
in
this manual.
Sort the parts and check against the
contents
list.
For
safety purposes we
strongly recommend the product to
be
assembled by
at least
two
people.
Some
parts
have
metal edges.
Please be
careful when handling components.
Always wear gloves, shoes and safety goggles during assembly.
Do
not
attempt
to assemble the
Gazebo
in
windy
or
wet conditions.
Dispose
of
all
plastic
bags safely
-
keep
them away from children's
reach.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the Gazebo
if
you
are
tired,
have
taken drugs,
medications
or alcohol, or
if
you
are
prone to dizzy
spells.
When using
a
stepladder
or
power tools,
make sure
that
you
are
following the
manufacturer's safety advice.
Do
not climb
or stand on the roof.
Heavy articles should
not
be
leaned against the poles.
Keep
roof
and
gutters
clean
of
snow,
dirt
& leaves.
Heavy snow load on
roof
can
damage the
Gazebo,
making it unsafe to stand
below
or nearby.
This
product
was
designed to
be used
mainly
as
a
Gazebo.
If the profiles' color
was
scratched
during
assembly, it
can be
fixed.
Light Transmission
-
15%
»
Cleaning Instructions
In
order to
clean
the
Gazebo,
use
a
mild detergent solution and rinse
with
cold
clean water.
Do
not
use
acetone, abrasive cleaners, or other special detergents to clean
the
panels.
»Tools
&
Equipment
TO01(Supplied)
6,
Attention
Please
make sure you install
the
panels
with the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT") and peel
the film strip covering the
panels.
Screws
and plugs
are
not supplied.
Please
tighten
all screws
when completing assembly.
Anchoring this product to the ground
is
essential
to
its
stability
and
rigidity.
It
is
required to complete this
stage
in
order for your warranty to
be
valid.
During Assembly
During assembly
use
a
soft surface below the parts to avoid scratches and damages.
When
encountering the information
icon, please refer
to the
relevant assembly step for additional comments and
assistance.
Step
8b:
Carefully spread silicone along the cross-section
of the profile
and
immediately
attach the profiles together.
It
is
recommended to wipe the extra
residue silicone.
Step
10: It
is
recommended to
use
a
carton
or
other soft material under the lowered
corner
in
order to avoid
scratches and peeling
of paint.
*This note
also
refers
to
step
18
Steps
13+14:
Optional
-
if
you wish to add curtains
/
mosquito netting
-
Please
thread the plastic clips through the
rail
in
each
profile.
(Curtains
/
mosquito netting
are
not supplied).
Add clips according to the specific
quantity of curtain
rings.
It
is
not
possible to add the clips at
a
later time, once the
product
is
fully
assembled.
Steps
19+21: Please
note
that
screws
insertion should
be
done from the outside.
Afterwards
please
use
the tool
TO01.
Steps
18+20: Please
note
that
screws
insertion should
be
done from the
bottom
up.
Step
23b:
Please
add silicone on the inner
area
of part
#8327
as
illustrated.
Step
29a:
Please
drill
holes
in
the
panels
to
be
located precisely parallel to the holes
in
the gutters' profiles.
Step
30:
Please
level
the profile's
legs and
adapt
screws
and plugs to your specific
ground type.
Publicidad
Tabla de contenido
