Publicidad
Idiomas disponibles
Idiomas disponibles
EN
PLEASE CAREFULLY READ THIS MANUAL
AND KEEP IT IN A SAFE PLACE
There are 4 buttons on the remote control: A, B, C and D
And 1 button at the front of the signalight : E
A
B
C
D
STEP ONE
Press the button (E) to switch it on : you would see a red flashing light turn on.
STEP TWO
Press the button A on the remote control to switch it on.
Press the upper arrow ( A ), to show you are going straight forward.
You will see this signal light on. If no other arrows are pressed,it will display until
you turn the signalight off.
Press the left arrow ( B ), to show you are turning left.
You will see left arrow will blink. To go back to Forward, press A.
Press the right arrow ( C ), to show you are turning right on the LED panel.
You would see right arrow will blink. To go back to Forward, press A.
Press the warning sign (D), when you would like to show a danger or a stop on
the signalight. You will see warning sign will blink until you press another button.
A brake motion sensor is integrated in the signalight. In case of a strong brake,
the red danger sign will turn on to warn people that you have stopped abruptly.
You will see all red LEDs on. Danger sign will disappear as soon as you start
moving again.
BATTERY USE FOR SIGNALIGHT AND REMOTE CONTROLLER
• Signalight: 2pcs AA batteries is need. Use coin to
• Remote Controller : 2pcs CR2025 batteries is need.
open (as below) and insert the batteries.
Please remove the battery
insulator tab before use.
HOW TO PLACE THE SIGNALIGHT ON THE BIKE?
Turn on the signalight, then mount it on back seat post/Rear bike rack:
E
HOW TO FIX THE REMOTE CONTROL ON YOUR BIKE ?
Wrap the silicon strap of remote control around the handlebars of your bicycle.
Special attention : mobile phone antennas may occasionally interfere with the communication
between the remote control and the signal panel. It is highly recommended that the user removes
the Signalight and Remote Contoller when parking outside. It is easy to take out and no tools needed.
PROCEDURES FOR PAIRING:
1. Press and hold the button E for 5 seconds to
2. Press and hold the "!" button of the Remote 5
enter the pairing mode. The red LED pattern will
be flashing to indicate it is in pairing mode.
3. Press "!" button of the Remote to confirm the
4. The LEDs of the remote and yellow LEDs of si-
pairing.
ES
B
PASO UNO
Presione el botón (E) para encenderlo: verá que se enciende una luz roja intermitente.
PASO DOS
Presione el botón A en el control remoto para encenderlo.
seconds to enter the pairing mode. All LEDs will
be flashing to indicate it is in pairing mode.
USO DE LA BATERÍA PARA EL INTERMITENTE Y EL CONTROL REMOTO
• Intermitente: se necesitan 2 pilas AA. Use una
moneda para abrir (como se muestra a continua-
ción) e inserte las baterías.
gnalight will turn on if pairing successful
INSTRUCCIONES IMPORTANTES.
MANTENGA PARA USO FUTURO: LEA CUIDADOSAMENTE
Hay 4 botones en el control remoto: A, B, C y D
Y 1 botón en la parte frontal del intermitente: E.
A
C
D
Presione la flecha superior (A) para indicar que sigue adelante.
Verá esta luz encendida. Si no presiona ninguna otra flecha, se mostrará esta
hasta que apague el intermitente.
Presione la flecha izquierda (B) para indicar que gira a la izquierda.
Verá que la flecha izquierda parpadea. Para volver a Adelante, presione A.
Presione la flecha derecha (C) en el panel led para indicar que gira a la derecha.
Verá que la flecha de la derecha parpadea. Para volver a Adelante, presione A.
Presione el símbolo de advertencia (D), cuando desee indicar un peligro o una
parada en el intermitente. Verá que el símbolo de advertencia parpadea hasta
que presione otro botón.
El intermitente tiene integrado un sensor de movimiento del freno. En caso de
frenadas bruscas, la señal de peligro roja se encenderá para advertir a las personas
que se ha detenido abruptamente.
Verá todos los led rojos encendidos. La señal de peligro desaparecerá tan pronto
como comience a moverse de nuevo.
• Control remoto: se necesitan 2 baterías CR2025.
Retire la lengüeta aislante de la batería
antes de usar.
E
Publicidad
