enbrighten SPECTRUM Guía Rápida

BEFORE YOU START
Inside the box you will find your Enbrighten Spectrum LED Puck Lights with detached rings,
remote, power supply, power cord, screws and mounting tape (pre-attached to pucks).
on/o
favorite modes
color bright +
select select
white bright
select select -
Organize Your Pucks: Carefully remove each puck from the box and lay it end to end in the
desired installation sequence. The power cord should be closest to the nearest outlet. Be sure
the installation surface is dry and will support the pucks. Use the cord management feature to
adjust the length of each puck as necessary, starting from the puck nearest to the power supply.
Once the pucks are aligned and spaced according your needs, wind up any excess cord into the
pucks. IMPORTANT: Make sure cords are laying flat during installation. Lights are intended for
indoor use only.
Cord Management Feature: To adjust
the cord length, tighten (clockwise) or
loosen (counterclockwise) the cords as
needed by twisting the center of each
puck. Note that the cord management
feature works best when starting from
the puck nearest to the power supply,
then adjusting each successive puck.
INSTALLATION
Install the power supply and pucks using the attached mounting tape or the included screws for
extra support.
STEP 1 - POWER SUPPLY
Using Mounting Tape
1. Remove the paper backing, align the power supply
and firmly press to secure it to the surface for 30
seconds.
Using Screws with Mounting Tape
1. Mark the screw locations of the two keyholes on the
back of the power supply.
2. Secure the screws to the marked locations using a
Phillips-head screwdriver.
3. Align the keyholes with the screws, mount the power
supply and fasten the screws as needed.
NOTE: The power supply must be facing the appropriate direction for the power cord to
reach the nearest outlet.
STEP 2 - PUCKS
Using Mounting Tape
1. Starting with the puck closest to the power supply,
mark the locations of each puck. Make sure the cord
is the appropriate length – it can be tightened after
installation using the cord management feature.
2. Each puck has two pieces of mounting tape. Peel off
the paper backings, align the puck and firmly press it
onto the surface for 30 seconds.
3. Repeat the process for each puck.
Using Screws with Mounting Tape
1. Mount the pucks to the surface as described above.
2. Gently extend the cord to its maximum length for each puck by twisting the center of
the puck counterclockwise. This provides a clear line of sight to the keyholes and avoids
potential damage caused by the screws.
3. Use a 3/32in.* drill bit to drill holes in each keyhole location.
4. Use a Phillips-head screwdriver to insert the provided screws into the holes. Tighten screws
as needed.
5. Repeat the process for each puck, maintaining the same orientation for each one.
Important — please read:
Refer to the manual or visit www.byjasco.com for limitations and restrictions on warranties and the product registration information.
WARNING: When using outdoor-use portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and
personal injury, including the following:
Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be used for the wet location portable luminaire. Receptacles are
available having built-in GFCI protection and are able to be used for this measure of safety.
WARNING: Keep these bags away from babies and children. Do not use in cribs, beds, carriages, or playpens. The thin film may cling to nose and mouth and
prevent breathing.
Warranty Information: This Jasco product is warrantied for three (3) years with a limited-lifetime replacement warranty on Enbrighten LED light source only.
MADE IN CHINA
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 3-year limited warranty.
Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-855-698-8324
between 7AM-8PM, M-F, Central Time.
Patents pending | www.enbrightenme.com
Tighten Loosen
Mounting Mounting
tape
tape
Keyhole for Keyhole for
mounting mounting
with screws with screws
Keyhole for
mounting with screws
Mounting Mounting Mounting
tape tape tape
Keyhole for
mounting with screws
40090 40091 40092
Version 1
08/27/20
STEP 3 - RINGS
Each puck has a ring that fits over the lens to protect the light and secure the cord.
Attaching the Rings
1. Feed the cords through the small openings on either side of the ring.
2. Twist the ring counterclockwise until it snaps securely into place.
3. To remove the ring, twist clockwise.
1.
STEP 4 - CONNECT TO POWER
Once the power supply and pucks are mounted, plug in the power cord to the nearest outlet.
OPERATION
Your Enbrighten Spectrum LED Puck Lights are paired with the included remote control. However, if you
want to pair additional puck sets or remotes, follow these steps: Within five seconds of plugging in the
pucks, press and hold the ON/OFF button on the remote. The lights blink twice to indicate they are paired
with the remote.
ON/OFF: Turns the pucks ON and OFF
Favorite: Press when on your preferred color or mode to recall later. Only
one setting can be saved.
on/o
Modes: Cycles through 10 color modes
favorite modes
Color Select: Cycles through 15 color options
color bright
+
select select
White Select: Cycles through six white light options
white bright
-
select select
Bright Select +/-: Adjusts the brightness level with full-range dimming
NOTE: To unpair the remote, press and hold the WHITE SELECT button.
Mounting the Remote: You can also mount the RF remote to a wall to operate as a light switch. Remove
the remote's body from the housing to reveal two mounting keyholes inside. Mark the keyhole locations
using a pencil, then drill holes using a 3/64in.** drill bit. Insert the screws leaving approximately 1/8in. from
the surface. Seat the remote's housing onto the screws and fasten as needed. Place the remote into the
housing.
NOTE: Your remote also comes with a magnetic strip on its back, allowing you to easily mount the remote
on most metal surfaces.
Pucks Model No. Input Watt, Max.
3 UCL/44/3/39/12/120 11.2
6 UCL/44/6/78/24/120 22.9
9 UCL/44/9/117/36/120 35.1
WARNING
RISK OF ELECTRIC SHOCK
• RECEPTACLE OUTLETS USED FOR POWERING
LANDSCAPE LIGHTS SHALL COMPLY WITH ALL
NATIONAL AND LOCAL ELECTRICAL CODES.
CONSULT LOCAL ELECTRICIAN IF UNSURE OF
COMPLIANCE REQUIREMENTS.
• FOR USE ONLY ON GFCI PROTECTED CIRCUITS.
• DO NOT SUBMERSE.
• DO NOT USE AROUND AQUARIUMS.
• LANDSCAPE LIGHTS ARE A WET-LOCATION
PRODUCT AND HAVE NO SERVICEABLE PARTS.
• DO NOT USE WITH EXTENSION CORD, NEAR WATER
OR WHERE WATER MAY ACCUMULATE.
• KEEP LAMPS AT LEAST 16 FEET FROM POOLS
AND SPAS.
• KEEP PLUGS AND RECEPTACLES DRY.
• AVOID DAMAGE TO THE CORDS AND LAMP
ASSEMBLIES DURING INSTALLATION. PERIODICALLY
INSPECT THE LANDSCAPE LIGHTS FOR PHYSICAL
DAMAGE OR OTHER DAMAGE CAUSED BY OUTDOOR
EXPOSURE TO THE ELEMENTS.
READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit https://byjasco.com/44090i
2. 3.
Location Use
Indoor
• REPLACE ANY DAMAGED LANDSCAPE
LIGHTS.
• DO NOT INSTALL IN LOCATIONS WHERE
LANDSCAPE LIGHTS CAN BE STEPPED ON.
• ENSURE LANDSCAPE LIGHTS ARE
UNPLUGGED FROM POWER DURING
INSTALLATION.
• CHILDREN SHOULD NOT PLAY WITH
LANDSCAPE LIGHTS.
• UL RECOMMENDS TESTING GFCI CIRCUITS
AND RECEPTACLES EVERY MONTH TO
ENSURE PROPER OPERATION.
RISK OF FIRE
• LANDSCAPE LIGHTS ARE DESIGNED TO
BE MOUNTED WITH THEIR INDIVIDUAL
KEYHOLE MOUNTING FEATURE. DO
NOT MOUNT LANDSCAPE LIGHTS USING
THE MAIN ELECTRICAL CORD OR THE
INDIVIDUAL DROP CORDS.
• NOT INTENDED FOR INSTALLATION IN
CEILINGS, SOFFITS, CABINETS, ATTICS, OR
OTHER ENCLOSED SPACES.