Tabla de contenido
Publicidad
SAFETY, OPERATORS, MAINTENANCE & PARTS MANUAL
2
INTRODUCTION
2.1 IMPORTANT
IMPORTANT: This is a precision machine and the service obtained from it depends on the way it is
operated and maintained.
This SAFETY AND OPERATORS MANUAL must be regarded as part of the machine. Suppliers
of both new and second-hand machines are advised to retain documentary evidence that this
manual was provided with the machine.
This machine is designed solely for use as a grass cutting machine operating within the
parameters listed in the specification pages. Use in any other way is considered as contrary to
the intended use. Compliance with and strict adherence to the conditions of operation, service
and repair as specified by the manufacturer, also constitute essential elements of the intended
use.
Before attempting to operate this machine, ALL operators MUST read through this manual and
make themselves thoroughly conversant with Safety Instructions, controls, lubrication and
maintenance.
Accident prevention regulations, all other generally recognized regulations on safety and
occupational medicine, and all road traffic regulations shall be observed at all times.
Any arbitrary modifications carried out on this machine may relieve the manufacturer of liability
for any resulting damage or injury.
It is important that during the life of the machine wearing and replaceable parts are disposed of in
an environmentally responsible way using the resources available in the country where it is used.
There are guidelines in this manual for the eventual decommissioning of the mower once it has no
further use.
Use only Ransomes Jacobsen Genuine spare parts to ensure the control of EC compliance
2006/42/EC
These are the Original instructions verified by Ransomes Jacobsen Limited
2.2 PRODUCT IDENTIFICATION
West Road
Ransomes Europark
Ipswich IP3 9TT
England
A
B
E
C
D
Kg
Kg
Kg
Kw
F
G
H
J
en-2
JACOBSEN FAIRWAY & T-PLEX CUTTING UNITS
A
Maximum front axle load in Kg (for machines
being driven on the highway)
B
Gross weight (mass) in Kg
C
Maximum rear axle load in Kg (for machines
being driven on the highway)
D
Power in Kw
E
Date code
F
Machine type (Designation)
G
Product code
H
Product name
J
Serial number
SAFETY, OPERATORS, MAINTENANCE & PARTS MANUAL
2
INTRODUCTION
2.3
GUIDELINES FOR THE DISPOSAL OF
SCRAP PRODUCTS
2.3.1 DURING SERVICE LIFE
Used oil, oil filters and engine coolant are
hazardous materials and must be handled in a safe
and environmentally responsible way.
In the event of a fluid leak, contain the spill to
prevent it entering the ground or drainage system.
Local legislation will dictate how such spills are to
treated.
Following the maintenance procedures laid out in
this manual will ensure that the impact the machine
has on the local environment is controlled.
When it has been identified that a turf care product
has no further functional value and requires
disposal, the following actions must be taken.
2.3.2 END OF SERVICE LIFE
These guidelines must be used in conjunction
with applicable Health, Safety and Environmental
legislation and use of approved local facilities for
waste disposal and recycling.
•
Position the machine in a suitable location
any necessary lifting equipment to be used.
•
Use appropriate tools and Personal Protective
Equipment (PPE) and take guidance from the
technical manuals applicable to the machine.
•
Remove and store appropriately:
1.
Batteries
2.
Fuel residue
3.
Engine coolant
4.
Oils
•
Disassemble the structure of the machine
referring to the technical manuals where
appropriate. Special attention must be made for
dealing with 'stored energy' within pressurised
elements of the machine or tensioned springs.
•
Any items that still have a useful service life
as second hand components or can be re-
serviced must be separated and returned to the
JACOBSEN FAIRWAY & T-PLEX CUTTING UNITS
relevant centre.
•
Other worn out items must be separated into
material groups for recycling and disposal
consistent with available facilities. More
common separation types are as follows:
• Steel
• Non ferrous metals
• Aluminium
• Brass
• Copper
•Plastics
•Identifiable
• Recyclable
• Non recyclable
• Not identified
• Rubber
• Electrical & Electronic Components
•
Items that cannot be separated economically
into different material groups must be added to
the 'General waste' area.
•
Do not incinerate waste.
•
Finally update machinery records to indicate
that the machine has been taken out of service
for
and scrapped. Provide this serial number to
Ransomes Jacobsen Warranty department to
close off relevant records.
en -3
Publicidad
Tabla de contenido
