Publicidad
Idiomas disponibles
Idiomas disponibles
POWER
100–240VAC~
50/60Hz, 2A
USE ONLY WITH A 250V FUSE
FUSE: T3.15A/250V
4
5
Antenna Splitter
These instructions are intended for the installer
of the audio transmission system . Please read
the instructions carefully prior to operation and
keep them for later reference . Figures 1 – 3 can
be found on page 2 .
1 Overview
1 BNC jacks, to install the reception antennas
on the front panel; for insertion of the jacks
refer to fig . 1
2 Power switch
3 Power LED
4 Rear side of the BNC jacks (1); connect the
jacks to the antenna inputs (7)
5 Mains jack for connection to a mains socket
via the mains cable provided
6 Power supply jacks for four receivers
7 BNC input jacks for the antenna signals
8 BNC output jacks to route the antenna sig-
nals to another antenna splitter UA-960
9 BNC output jacks to distribute the antenna
signals to the antenna inputs of four receiv-
ers
2 Safety Notes
This device corresponds to all relevant directives
of the EU and is therefore marked with
WARNING The device uses dangerous mains
voltage . Leave servicing to skilled
personnel only . Inexpert han-
dling may result in electric shock .
•
The device is suitable for indoor use only . Pro-
tect it against dripping water, splash water
and high air humidity . The admissible am-
bient temperature range is 0 – 40 °C .
•
Do not place any vessels filled with liquid,
e . g . drinking glasses, on the device .
•
Immediately disconnect the mains plug from
the socket
1 . if the device or the mains cable is visibly
damaged,
2 . if a defect might have occurred after the
device was dropped or suffered a similar
accident,
3 . if malfunctions occur .
In any case the device must be repaired by
skilled personnel .
•
Never pull the mains cable to disconnect the
mains plug from the socket, always seize
the plug .
•
For cleaning only use a dry, soft cloth; never
use water or chemicals .
•
No guarantee claims for the device and no
liability for any resulting personal damage
or material damage will be accepted if the
device is used for other purposes than origi-
ANT. A OUTPUT
ANT. A CASCADE
1.
DC Output
+12V 1A x 2
6
7
8
nally intended, if it is not correctly connected,
or if it is not repaired in an expert way .
If the device is to be put out of opera-
tion definitively, dispose of the device
in accordance with local regulations .
3 Applications
The antenna splitter UA-960 is designed for
operating up to four UHF receivers from JTS
which
– operate in a frequency range between 470
and 960 MHz
– are equipped with removable antennas (BNC
connection)
– are supplied with +12 V/1 A max .
UA-960 makes it easier to set up the audio
transmission system: Only two of the antennas
supplied with each receiver (one pair for each
receiver) are required for connection to the
antenna splitter; all other antennas and the
power supply units of the receivers are not
required . The splitter will send the antenna
signals to the receivers and supply the receivers
with power . Matching connection cables are
supplied .
When more than four receivers are op-
erated, the cascade outputs (8) can be used
to connect multiple antenna splitters UA-960
in series . Each antenna splitter will be able to
supply four receivers with power .
.
The antenna splitter can also be used in com-
bination with two antenna signal amplifiers
UB-900I . The antenna splitter will supply the
amplifiers with power .
4 Operation
4.1 Preparation and setting up
1) When the antenna signal amplifiers UB-900I
are used, the 12 V supply voltage for these
amplifiers must be available at the jacks
ANT . A and ANT . B (7) . Prior to operation,
please make sure that the corresponding
switch for the supply voltage in the device is
in the position ON (fig . 2 on page 2) .
WARNING
Before opening the device, always make
sure that the mains plug is disconnected
from the socket!
2) To install the reception antennas on the front
panel of UA-960, insert the two BNC jack-
to-jack adapters supplied with the device
into the mounting holes on the left and on
the right and screw them on (refer to fig . 1
on page 2) .
3) Place the antenna splitter on a flat surface or
install it into a rack for devices with a width
2.
3.
4.
4.
3.
9
Only skilled personnel should
open the device and adjust
the switch .
ANT. B OUTPUT
2.
1.
CASCADE
ANT. B
+12V 1A x 2
8
7
6
of 482 mm (19") . For installation into a rack,
1 rack unit (= 44 .45 mm) is required .
4.2 Connection and switching on
The connection options can be found in fig . 3
on page 2 .
1) Connect the low voltage jacks DC Output (6)
to the power supply jacks of the receivers .
2) Connect the antenna pair of one of the re-
ceivers to the antenna inputs of the splitter:
– either to the two jacks (1) on the front
panel of the device; in this case, connect
the rear side (4) of these jacks to the jacks
ANT . A and ANT . B (7)
– or directly to the two jacks ANT . A and
ANT . B (7) on the rear panel of the device .
When using the antenna signal amplifiers
UB-900I, insert the amplifiers between the
antennas and the antenna splitter .
3) Connect the two antenna inputs of each re-
ceiver to an antenna output ANT . A 1 . ... 4 .
and to the corresponding antenna output
ANT . B 1 . ... 4 . (9) .
4) The antenna signals can be routed to an-
other UA-960: Connect the outputs ANT . A
CASCADE and ANT . B CASCADE (8) to the
inputs ANT . A and ANT . B (7) of the following
UA-960 . This splitter in turn allows connec-
tion of four receivers .
5) Connect the mains cable provided to the
mains jack (5) and connect the mains plug
of the cable to a mains socket .
6) To switch the antenna splitter on or off, use
the rocker switch (2) . When the device is
switched on, the power LED (3) will light up .
5 Specifications
Frequency range: � � � � � � � � 470 – 960 MHz
RF amplification: � � � � � � � � 3 dB
DC voltage outputs:� � � � � � +12 V, 1 A (4 ×)
Ambient temperature: � � � � 0 – 40 °C
Power supply: � � � � � � � � � � ~100 – 240 V / 50 – 60 Hz
Power consumption: � � � � � 60 W
Antenna connections: � � � � BNC jacks, 50 Ω
Dimensions (W × H × D): � 482 × 45 × 250 mm,
1 rack unit
Weight: � � � � � � � � � � � � � � � 2�15 kg
Subject to technical modification .
All rights reserved by MONACOR
GmbH & Co. KG. No part of this instruction manual
may be reproduced in any form or by any means for
any commercial use.
DC Output
4
®
INTERNATIONAL
5
Publicidad
