Environmental Protection; Technical Data - Metabo BSA 12-18 LED 2000 Manual Original

11 Hook (for hanging)*
12 screw thread (5/8"-UNC) for fastening the lamp
to a stand*
13 Cut-out slot for wall suspension*
14 Hole (16 mm diameter) for fastening to a stand*
15 Cover cap (mains connection)*
16 Socket (mains connection)*
17 Plug (of the mains connection)*
18 Lock ring*
* depending on model/equipment/not in scope of
delivery
3. Use
3.1 Inserting and removing the battery pack
Charge the battery pack (9) (depending on
equipment) before use.
1. Press button (8) and fold open the protective
cover (7) .
2. Slide on the battery pack (9) or remove it.
3. Close the protective cover (7) .
The ideal storage temperature for battery packs is
between 10°C and 30°C.
3.2 Switching on/off, setting the light
intensity
Do not direct the light beam into the eyes of
people or animals.
1. Turn on and off at the switch (5).
2. Change the light intensity by turning the ring (6)
. When the maximum or minimum light intensity
is reached, the light beam flashes briefly.
3.3 Capacity display (4)
When the lamp is switched on, the charge level of
the battery pack is shown by the LED lights.
3.4 USB connection (only for BSA 18 LED
4000, BSA 18 LED 10000)
The charger is suitable for charging/operation of
electronic devices with a USB interface (like
Smartphones, MP3 Players, tablets, etc.) - no data
exchange
Only connect USB devices which are
compatible with the USB standard. Using
incompatible USB devices can lead to
malfunctions, damage or injury.
1. Open the cover cap of the USB port (3).
2. Plug the USB device into the USB port (3) using
a suitable USB cable.
3. Disconnect the USB cable from the device after
charging/use and close the cover cap.
Note: IP protection is only guaranteed when the
cover of the USB port (3) is closed.
3.5 Mains connection (only for BSA 18 LED
10000)
Before commissioning, check that the rated
mains voltage and mains frequency stated on
the type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Connecting the mains connection:
1. Open cover cap (15).
2. Align the connector (17) of the mains connection
in such a way that thee socket (16) and
connector (17) fit into each other.
3. Plug the connector (17) into the socket (16) . In
doing so, the locking ring (18) turns
automatically and locks the connector (17)
against being pulled out.
Removing the mains connection:
1. Turn the locking ring (18) anti-clockwise and pull
off the connector (17) .
2. Close again the cover cap (15) .
4. Troubleshooting
Brief flashing of the light beam every 3 minutes
signals that the battery pack is almost empty and
must be recharged.
5. Cleaning
Remove the battery pack from the device or
pull the mains plug before carrying out
cleaning.
Do not clean with aggressive cleaning agents.
Ensure that the lamp and the battery contacts are
dry before inserting the battery pack.
6. Repairs
Repairs to Metabo machines must be carried
out by qualified electricians only!
If any of your Metabo power tools require repairs,
please contact your Metabo service centre. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.

7. Environmental Protection

Do not allow battery packs to come into contact with
water!
Protect the environment and do not dispose
of power tools or battery packs in household
waste. Observe national regulations on
separated collection and recycling of disused
machines, packaging and accessories.
Before disposal, discharge the battery pack in the
tool. Prevent the contacts from short-circuiting (e.g.
by protecting them with adhesive tape).

8. Technical Data

Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Only to be used with original Metabo battery packs:
12 V (only 12-18...): 625406000, 625349000, etc.
ENGLISH en
11