Publicidad
Idiomas disponibles
Idiomas disponibles
BLUETOOTH STEREO TOWER
SPEAKER WITH FM PLL RADIO
Please read following instructions prior to
operate your unit.
Manufacturer of this unit follows a principle
of continuous improvement and has no
responsibility for any changes that are made
to the unit nor any liability for these changes.
Thanks for your choice of our products.
(see picture 1)
MAIN UNIT
1. BLUETOOTH INDICATOR
2. POWER ON/STANDBY BUTTON
4. VOLUME+ BUTTON
5. TUNING/SKIP/SEARCH DOWN BUTTON
6. TUNING/SKIP/SEARCH UP BUTTON
7. PAIR/PLAY/PAUSE BUTTON
8. SOURCE BUTTON
9. LCD DISPLAY
11. AUX IN JACKS
12. LINE IN JACK
14. AC CORD
REMOTE CONTROL
(see picture 2)
1. SOURCE BUTTON
2. MUTE BUTTON
5. NUMERIC BUTTONS
8. POWER ON/STANDBY BUTTON
9. PAIR/PLAY/PAUSE BUTTON
11. MEM+ BUTTON
12. CLOCK BUTTON
14. TUNING/SKIP/SEARCH UP/DOWN
BUTTONS
POWER SUPPLY
Plug AC plug into the outlet socket for
connecting the main power.
Note: During playback, if not any operation in
about 6 hours, the unit will switch to standby
mode automatically.
SLEEP TIMER SETTING
You can set the sleep timer at power on
modes as following instructions:
Press SLEEP button on the remote control
2
repeatedly to cycle through the sleep time
options:
After the sleep time setting, you can play the
unit freely. Once the sleep time is expired, the
unit will be switched off.
During playback, press SLEEP button once to
check the remaining sleep time.
HOW TO SET TIME
At the standby mode, press and hold CLOCK
the screen; use TUNING UP/DOWN button
your adjustment by pressing CLOCK button
on the remote; Minute starts blinking on the
screen, press TUNING UP/DOWN button on
the remote to set the minute accordingly, press
your setting.
During playback, press CLOCK button to
check the current time.
Note: The time only could be set on standby
mode.
BLUETOOTH OPERATING
This unit can receive stereo audio signal from
a BLUETOOTH stereo audio source device.
1. Power on the unit, switch to BLUETOOTH
mode by pressing SOURCE repeatedly.
2. Bluetooth LED indicator rapid blinking while
it is pairing.
BLUETOOTH audio source device. If
4. Pairing successful (LED indicator blue
lights up), ready to stream music.
5. During playback, press TUNING UP/
DOWN button to skip to the next or
previous track. Press and hold TUNING
UP/DOWN button to fast forward or
backward.
NOTE:
minutes when there is no devices for
pairing.
instructions on BLUETOOTH connectivity
for your device, please consult your
mode, it will connect to the last
paired external BLUETOOTH device
automatically.
RE-CONNECT TO THE BLUETOOTH
AUDIO SOURCE DEVICE
If the device is already paired with the
connect them by following steps:
the audio source device. The Bluetooth
indicator will blink for about 1.5 minutes for
connecting.
for connecting. Bluetooth indicator will turn
using Bluetooth operation of the device to
be connected.
FM RADIO
TUNING THE FM RADIO
1. Power on the unit, switch to TUNER
(RADIO) mode by pressing SOURCE
repeatedly.
tune radio station. Press and hold TUNING
UP/DOWN button to auto search radio
station forward or backward respectively
(When an available station will be found,
the unit will broadcast it immediately and
the searching will be stopped).
the frequency via numeric buttons on the
remote control. For example, press buttons
8, 9 and 8 to get to 89.8MHz; If access a
the screen.
4. During radio playback, press MO/ST button
on the remote to switch between FM
STEREO and FM MONO modes.
STORING YOUR FAVORITE RADIO
STATION
1. During playback, press MEMORY button
on the remote for storing the current station
the screen.
to select the corresponding memory cell
MEMORY button on the remote.
4. During radio playback, press MEM+ or
recall the stored stations.
MUTE THE UNIT
During playback, press MUTE button to
switch off the audio. Press the button again to
resume the audio.
VOLUME LEVEL/TREBLE/
BASS ADJUSTMENT
output level or treble effect or bass effect.
RESET BUTTON
When using the unit, you will come across
halt accidentally; you can use a needle or a
small, slender implement to poke the RESET
button in the rear of the player, the unit will
turn off automatically and then please reboot
the unit, the unit will recover the factory preset
condition.
CONNECTING WITH
OTHER APPLIANCES
AUX IN
1. Connect the AUX IN jacks on the unit to
audio source, for example, DVD player with
an RCA cable.
2. Press the POWER button on the unit or
STANDBY button on the remote to turn the
unit on.
switch to AUX mode.
4. Use the native controls on the connected
audio device to begin playing music
through the connected unit.
LINE IN
Follow steps to connect the unit to another
audio device:
1. Connect the device into the player LINE
IN jack with the LINE OUT cable (not
included).
2. Press POWER button on the unit or
STANDBY button on the remote to turn the
unit on.
switch the unit to Line In mode.
4. Power on the device and begin play.
CAUTION
dripping or splashing and that no objects
placed on the apparatus.
Publicidad
