Technical Data - Felisatti RF55/1000E Instrucciones De Servicio

TECHNICAL DATA

Milling machine
Absorbed power
 of milling cutter attachment
No load speed
 maximum of milling cutter
Lengthwise travel
Machine weight (without accessories)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILUSTRATIONS
DESCRIPTION (See figures)
A Start-up switch (Fig.1)
B Spindle lock of shaft (Fig.1)
D Clip fixing nut (Fig.1)
E Depth stop (Fig.1)
F Stepped stop (Fig.1)
G Locking wing nut (Fig.1)
H Fixing lever (Fig.1)
I Side stop (Fig.1 and Fig.2)
J Transparent frontal protection (Fig.1 and Fig.2)
K Dust suction adapter (Fig.1 and Fig.3)
L Speed adjustment (Fig.1)
M Depth adjustment scale (Fig.1)
O Grips (Fig.1)
P Base plate (Fig.1)
Q Sliding plate (Fig.1)
R Wing screw for dust suction adapter (Fig.1 and Fig.3)
S Strip stop (Fig.2)
T Parallel stop fine adjustment (Fig.1 and Fig.2)
V Wing screw (Fig.1, Fig.2 and Fig.3)
EQUIPMENT
- Clip  8 mm
- Side stop
- Fixed spanner 17 mm
- Transparent guard
- Dust suction adapter
- Operating instructions
- Safety instructions
- Warranty
SAFETY INSTRUCTIONS
 See "Safety Instructions" enclosed manual, supplied
 WARNING! The dust produced when milling asbestos
together with this instruction manual.
and/or silica stone materials is dangerous to health.
Follow the insurance company's safety instructions
regarding the responsibility of employees.
W
rpm
mm
mm
mm
kg
 For your personal safety, always connect the machine
to a mains supply by a differential and thermal cut-out
switch, in accordance with regulations on low-voltage
 Do not perforate the machine casing, as this would
wiring sitemaps.
 Always unplug the machine before doing any work on it.
destroy the protective insulation (use adhesive labels).
 Always stop the machine by switching it off, not by
 WARNING! Before each use, inspect the plug and
unplugging it.
lead. Should they need replacing, have this done by an
official service centre. Only plug the machine in when it
 Always keep the lead out of the machine's working
is switched off.
 Only plug the machine in when it is switched off.
area.
 Do not allow the machine to get wet, nor should it be
 When using the machine, always wear safety goggles,
used in wet environments.
gloves and non-slip footwear, and it is advisable to
 Check for correct piece fixing before commencing any
wear ear protection.
 Only milling heads with acceptable revolutions that are
operation.
at least the same as the maximum off-load revolutions
 The milling head shaft diameter should match the
of the machine should be used.
 It should be ensured that the milling head is firmly held
inside diameter of the tool-holder (locking clip).
 The clip-carrier shaft support lever must only be oper-
in place before the machine is operated.
 The milling head should only be brought into contact
ated when the machine is stopped.
 The machine must be firmly held by the grips. Other-
with the work-piece after it has been switched on.
wise the recoil produced could cause the machine to
 Hold the machine firmly in both hands and in a stable
work imprecisely or even dangerously.
 The milling machine must never be used on metal
position.
 Hand must be kept clear of the milling machine while it
objects, such as nails and screws.
 The cutting depth must never be adjusted with the
is operating.
motor running. A mistake in this time could lead to
personal injury and/or damage to the milling head or
 The operator should remain alert and keep the milling
work-piece.
 When the milling operation has been completed,
head apart from all objects during operation.
locking lever should be operated so that the machine
returns to its upper starting position.
RF55/1000E
1000
20000-27000
8
0-55
36
3.75