Line-In Operation; Care And Maintenance - Tokai TB-207 Manual De Instrucciones

PROGRAM FUNCTION (IN CD/MP3 or USB MODE)
To Program Specific Tracks (up to 20 tracks)
1. Load the CD/MP3 disc or USB you wish to program.
2. Make sure the CD/MP3 disc or USB is in stop mode.
3. Press the PROGRAM/REPEAT button once, "P01" will
display on the LCD and "PROG" indicator will blink.
4. Press the SKIP / buttons until the desired track
number is reached.
5. Press the PROGRAM/REPEAT button to store the
selection.
6. Repeat the (4) & (5) steps until you have entered all the
tracks.
7. To play the stored sequence, press the PLAY/PAUSE
button.
8. After all memory tracks have been played, the CD or USB
player will stop automatically.
Notes:
1. When 20 tracks of CD/MP3 or USB have been
programmed, the memory is full. The programmed tracks'
LINE-IN jack will allow you to connect external music player or external sound source to the main unit.
1. Plug into a 3.5mm audio cable (not included) into your
external music player and connect the other end
(3.5mm jack) into the LINE- IN jack on the side of the
unit.
2. Make sure your external music player is turned on.
3. Slide the FUNCTION switch to LINE IN position on the
unit. The unit will enter LINE IN mode automatically.
4. Start music playback on your external music player.
*Carrying for Compact Discs
1. Treat the disc carefully. Handle
the disc only by its edges. Never
allow your fingers to come in
contact with the shiny, unprinted
side of the disc.
2. Do not attach adhesive tape,
stickers, etc. to the disc label.
3. Clean the discs periodically with a
soft, lint-free, dry cloth. Never use
detergents or abrasive cleaners to
clean the disc. If necessary, use a CD
cleaning kit. If a disc skips or gets stuck
on a section of the disc, it is probably
dirty or damaged (scratched). When
cleaning the disc, wipe in straight lines
from the center of the disc to the outer
edge of the disc. Never wipe in circular motions.
4. This unit is designed to play discs bearing the
identification logo as shown here or MP3 format Disc. Other
discs may not conform to the CD standard and may not play
properly.
5. Discs should be stored in their cases after each use to
avoid damage.
All manuals and user guides at all-guides.com

LINE-IN OPERATION

CARE AND MAINTENANCE

11
numbers will show on the LCD display sequentially. Then
the location "P01" shows on LCD display and flash. You
can press PLAY/PAUSE
playback. Or repeat (4) & (5) steps to change the track
number you wish.
2. If you want to cancel the program memory, press the
STOP button twice during playback or once in STOP
mode.
The Repeat function also applies to programmed track
playback.
To repeat programmed tracks
1. During program play, press PROGRAM/REPEAT button
once will repeat the specifically programmed tracks.
2. Press the PROGRAM/REPEAT button again will repeat
all the programmed tracks.
3. Press the STOP button twice to cancel program
playback.
5. Adjust VOLUME knob to control the sound level of
music playback from the speakers on the unit.
6. Remember to disconnect the connection cable from the
unit after use in order to be able to listen to CD/MP3
disc or USB music.
6. Do not expose discs to direct sunlight, high humidity, high
temperatures, or dust, etc. Prolonged exposure or extreme
temperatures can warp the disc.
7. Do not stick or write anything on either side of the disc.
Sharp writing instruments or the ink may damage the
surface.
* Care of the Cabinet
1. To prevent fire or shock hazard, disconnect your unit from
the AC power source when cleaning.
2. The finish on your unit may be cleaned with a dust cloth
and cared for as other furniture. Use caution when cleaning
and wiping the plastic parts.
3. Mild soap and a damp cloth may be used on the front
panel.
* To Clean the Lens
If the lens get dirty, your player may skip or may not play a
CD
1. Open the CD door.
2. Use a camera lens blower/brush to blow on the lens once
or twice, brush the dust or particles off the lens then blow
again.
3. To remove fingerprints, use a dry cotton swab to wipe
from the middle to outer edge of the lens.
to start the program