Setting The Alarm; Snooze Function; Listening To Radio - essentiel b Lumin'Up II Instrucciones De Uso

Setting the alarm

In addition to the sunrise simulator, your radio alarm clock allows you to programme 2 alarms at
different times. To do this, the time must have been set beforehand (see previous paragraph). You
can select:
the buzzer or
•
the radio, or
•
the "Nature sounds" programme.
•
Note: to set the alarms, the MUSIC function must be disabled. To turn off the MUSIC function,
press the button.
To start setting the alarm, press on Alarm 1
1.
To start the setting cycle, long press on Alarm 1
2.
To scroll through the different setting steps, press once or several times on Alarm 1
3.
Alarm 2 .
The setting cycle is as follows:
Hour > Minute > Alarm frequency > Type of alarm > Light intensity.
When one of the setting steps has been selected, it starts to flash.
Use the (decrease) and (increase) buttons to reach the number you want. To make the
4.
numbers scroll faster, keep the button pressed down.
To save the number, press on Alarm 1
5.
cycle automatically moves to the next step.
When the alarm has been set, AL1 or AL2 is displayed next to the time on the luminous
6.
display screen.
Type of alarm:
"BUZZER" mode
Sign on the display
"bu"
screen
/
Additional step(s) of
the setting cycle
Intensity of luminous alarm:
You can adjust the intensity of luminous alarm: "L01" to "L20" or switch it to the OFF position.
30 minutes before the alarm time, the lamp lights up at the level "L01".
•
The light intensity increases gradually, until it reaches the programmed level.
•
If you programme an alarm less than 30 minutes before the time displayed, the lamp does
•
not light up.
20
or Alarm 2 .
or Alarm 2 . The hour digit flashes.
or
or Alarm 2 . The digit stops flashing and the setting
"RADIO" mode "NATURE SOUNDS"
mode
Last frequency "nS"
diffused
- Adjusting the - Choosing the nature
volume sound ("n-1", "n-2" or
"n-3")
- Adjusting the
volume
C :
omments
When you set the alarm frequency, you can choose between:
•
- "1-5": from Monday to Friday
- "1-7": every day
- "6-7": weekend only
- "1", "2", "3", "4", "5", "6", "7": one day only (each number corresponds to a day of the week,
for example, "1" corresponds to Monday)
When an alarm is programmed, you can display the alarm time whenever you want by briefly
•
pressing the Alarm 1 or Alarm 2 button. The programmed alarm time is displayed and
disappears after a few seconds.

SNOOZE FUNCTION

When the alarm goes off, "AL1" or "AL2" starts flashing. Press the button
will come back on again after 9 minutes.
TURNING OFF THE ALARM
When the alarm goes off, "AL1" or "AL2" starts flashing. Press on
to turn it off.
C :
omments
This operation enables you to automatically reactivate the alarm for the next day.
•
If you take no action, the alarm will ring for 30 minutes.
•
ENABLING AND DISABLING THE ALARM FUNCTION
To enable or disable a preset alarm, press and hold down the Alarm 1
"AL1" or "AL2" appears/disappears next to the time shown on the luminous display screen.

Listening to radio

To listen to the radio, press the button to enable the MUSIC function.
1.
Then select RADIO mode by pressing on the SOURCE button to scroll through the modes. The
2.
selection cycle is as follows:
Radio > Nature sounds > Auxiliary source
The RADIO mode is indicated by the display of the frequency.
Extend the antenna wire on the back of the device for better FM reception.
To automatically scan for frequencies, press and hold the
3.
button. The scan stops when a radio station has been found. To interrupt the scan, press briefly
on either of buttons again.
To do a manual search, briefly press on the
4.
press, the frequency decreases or increases by 0.1 MHz.
To turn off the radio, briefly press the button.
5.
. The alarm stops and
to mute the alarm, then on
or Alarm 2 button.
(decrease) or (increase)
(decrease) or (increase) button. With each
21