Technical Data - EINHELL TC-SR 18 Li BT Manual De Instrucciones

4. Technical data

Power supply: ......................................18 V
Speaker output............................ .....2 x 3.0 W
Volume max. ............................... .... 85 dB (A)
USB output voltage..................... ......5 V
USB output current..................... ................ 2 A
AUX connection ................................
Weight (Tool only)........... ......... 0.64 lbs (0.29 kg)
5. Operation
5.1 Switching the cordless speaker on and
activating Bluetooth
•
Push the cordless speaker onto the battery
(not included) until it snaps into place.
•
To switch the cordless speaker on, press and
hold the On/Off switch (1) until you hear the
start signal.
•
The cordless speaker is now switched on and
Bluetooth is activated.
®
•
Activate Bluetooth
tablet PC and link it with "PXC Speaker".
•
Once the connection has been established,
the speaker can be used.
•
To switch the cordless speaker off, press and
hold the On/Off switch (1) until you hear the
off signal.
Important! If the device fails to switch on, press
the switch for the battery charge level indicator (9)
on the rechargeable battery and try again.
5.2 Operating the activated cordless speaker
(Fig. 1/Items 1, 2, 3)
Reduce volume:
Press the - Button (2) once briefl y.
Increase volume:
Press the + Button (3) once briefl y.
Previous title:
Press the - Button (2) once for a few seconds.
Next title:
Press the + Button (3) once for a few seconds.
Mute:
Press the On/Off switch (1) once briefl y.
Anl_TC_SR_18_Li_BT_USA_SPK7.indb 11 Anl_TC_SR_18_Li_BT_USA_SPK7.indb 11
⁄ '' (3.5 mm)
1
8
(Fig. 1/Item 1)
®
on your smartphone or
®
EN
5.3 Charging using the USB output (Fig. 1/
Item 4)
Important! The USB port is only suitable for
charging and cannot transfer any audio fi les
•
Push the cordless speaker onto the battery
(not included) until it snaps into place.
•
Connect the device that is to be charged to
the USB output (4) of the cordless speaker
using a suitable USB cable.
•
To activate the USB output (4), press the On/
Off switch for the USB output (6) briefly. It will
then light up blue.
•
Deactivate the USB output (4) by holding the
On/Off switch for the USB output (6) down
until it goes out.
•
If no device is connected, the USB output (4)
will be deactivated after approx. 3 min., and
the On/Off switch for the USB output (6) will
go out.
5.4 Using the AUX connection (Fig. 1/Item 5)
Connect the smartphone or tablet PC from which
you want to play back audio fi les to the AUX input
(5) on the cordless speaker using an AUX cable
( ⁄ '' (3.5 mm) jack plug).
1
8
Important! Using the AUX and USB ports with
the same device at the same time will adversely
aff ect the sound quality and is therefore not
recommended.
5.5 Charging the Lithium-Ion battery (not
included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
5.6 Battery capacity indicator (Fig. 3 / item
10)
Press the battery capacity indicator switch (9).
The battery capacity indicator (10) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
- 11 -
26.04.2022 15:31:26 26.04.2022 15:31:26