Westin 22-1185 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
TROUSSE DE MONTAGE
22-1185
CHROME/ CROMADO /CHROME
22-0050
BLACK/NEGRO/NOIR
22-0055
ITEM QTY
1 2 STEP BAR (PURCHASED SEPARATELY)
2 2 FRONT BRACKET
3 4 REAR AND CENTER BRACKET
4 12 M8-1.25 x 25MMHEX HEAD BOLT
5 12 5/16" FLAT WASHER
6 12 5/16" LOCK WASHER
7 12 1/4-20 X .75 T-HEAD BOLT
8 12 1/4" FLAT WASHER
9 12 1/4-20 NYLON INSERT LOCK NUT
1 2 ESTRIBOS, (SE COMPRA SEPARADO)
2 2 PIEZAS DE SUJECIÓN DELANTERAS
3 4 PIEZAS DE SUJECIÓN TRASERAS Y CENTRALES
4 12 PERNOS CON CABEZA HEXAGONAL DE M8-1,25 X 25MM
5 12 ARANDELAS PLANAS DE 5/16"
6 12 ARANDELAS DE PRESIÓN DE 5/16"
7 12 PERNOS CON CABEZA EN T DE 1/4-20 X .75"
8 12 ARANDELAS PLANAS DE 1/4"
9 12 TUERCA DE FIJACIÓN HEXAGONAL 1/4-20
1 2 MARCHE-PIEDS, (ACHETE SEPAREMENT)
2 2 SUPPORTS AVANT
3 4 SUPPORTS ARRIERE ET CENTRAL
4 12 BOULONS A TETE HEXAGONALE M8-1.25 X 25MM
5 12 RONDELLES PLATES 5/16 PO
6 12 RONDELLES A FREIN 5/16 PO
7 12 BOULONS A TETE-T 1/4-20 X .75 PO
8 12 RONDELLES PLATES 1/4 PO
9 12 1/4-20 ÉCROU DE BLOCAGE SIX PANS
STEP 1.
Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before
beginning.
STEP 2.
Install front brackets as shown. Hand tighten.
STEP 3.
Install rear and center brackets as shown. Hand tighten.
STEP 4.
Slide T-head bolts on step bar as shown (3 per slot, 6 per bar). Place step bar on saddle with long step pad forward and
end cap screw facing inward. Assemble with 1/4" fasteners.
STEP 5.
Make sure step bar and brackets are properly aligned. Tighten and torque M8 fasteners to 22 FT. LBS. and 1/4" fasteners
to 9 FT. LBS.
FINISH PROTECTION
Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g.
Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to
corrosion.
PASO 1.
Retire el contenido de la caja y verifique que ninguna pieza se haya dañado. Verifique que no falte ninguna
pieza. Lea las instrucciones completamente antes de comenzar.
PASO 2.
Instale los soportes delanteros como se muestra. Apriete con la mano.
PASO 3.
Instale los soportes centrales y traseros como se muestra. Apriete con la mano.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: '03 & UP TOYOTA 4-RUNNER (ROCKER PANEL)
APLICACIÓN: TOYOTA 4-RUNNER (PANEL BAJO LA PUERTA) MOD. 2003 Y SUPERIOR
APPLICATION: '03 ET PLUS TOYOTA 4-RUNNER (BAS DE CAISSE)
1
CONTENTS - CONTENIDO - CONTENU
SEE FIGURE 1.
SEE FIGURE 2.
SEE FIGURES 3 AND 4.
VEA LA FIGURA 1.
3
2
TOOLS - HERRAMIENTA
7/16" SOCKET
13MM SOCKET
RATCHET
TORQUE WRENCH
DADO DE 7/16"
DADO DE 13MM
MANERAL
LLAVE DE TORQUE
DOUILLE 7/16 PO
DOUILLE 13MM
CLIQUET
CLEF DE COUPLE
VEA LA FIGURA 2.
WO:
75-0648 REVISION A 4/21/06
- OUTILS