Application; Warning; General Safety; Safety Instruction - MaxPro PROFESSIONAL MPEAC1502/24D Manual

An es a of the level of exposure to vibra
switched off or when it is running but not actually doing the job. This may significantly reduce the exposure
level over the total working period.
Iden fy safety measures to protect the operator from the effects of vibra
the tool and the accessories, keep the hands warm, organisa

APPLICATION

Read this manual carefully before opera g or servicing this, air compressor to familiarize yourself with
proper safety, and main tenance procedures. FAILURE TO COMPLY WITH INSTRUCTIONS IN THIS MANUAL
COULD RESULT IN PERSONAL INJURY, PROPERTY DAMAGE, AND/OR VOIDING OF YOUR WARRANTY.
Following the ins
are devoted to con
the technical performance and design concept of products may vary without any prior
for any possible incurrence of inconvenience therefrom. Read and follow the opera ng instru ons and
safety informa efore using for the firs

WARNING

THINGS TO DO BEFORE OPERATING
YOUR NEW COMPRESSOR FOR THE FIRST TIME
On the top front of the compressor you will find a white plas
Hole. Remove the shipping plug and replace by pressing the red Oil Filler Plug(supplied in the parts bag)
into the Oil Filler Hole
2. Also, supplied in the parts bag you will find a black Air Breather Assembly. Screw the assembly into the
hole on the side and at the top of the Compressor Head
3. Using the Sight-Glass built into the lower front area of the Compressor (just behind the Regulator), check
the Oil Level. It should be at the halfway mark on the Sight Glass for normal opera
add oil, please use any standard air compressor oil available at Home Centers and other major retailers.
4. There are Air Outlet Fi on the Regulator. Air flow for one fi
Handle. The other is a free flow directly from the tank. Screw either a metal cap or a quick-coupler (not
supplied) onto the free-flowing fi ng before st
working with air fi to prevent leakage

GENERAL SAFETY

DANGER- AN IMMEDIATE HAZARD THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE
1. TO REDUCE THE RISK OF FIRE OR EXPLOSION, NEVER SPRAY FLAMMABLE LIQUIDS IN A CONFINDED
AREA. It is normal for the motor and pressure switch to produce sparks while opera
contact with vapors from gasoline or other solvents, they may ignite cause fire or explosion. Always operate
the compressor in a well-ven ated area. Do not smoke while spraying. Do not spray where sparks or flame
are present. Keep compressor as far from spray area as possible
2. The solvents Trichloroethane and Methylene Chloride can chemically react with aluminum used in paint
spray guns, paint pumps, etc, and cause an explosion. If you are using these solvents, use only stainless
steel spray equipment. This does not affect your compressor, but many affect the equipment being used
3. Never directly inbale the compressed air produced by a compressor. It is not suitable for breathing
purposes
WARNING- A POTENTIONAL HAZARD THAT COULD CAUSE SERIOUS INJURY OR LOSS OF LIFE
1. Do not weld not the air tank of this compressor. Welding on the air compressor tank strength and cause
an extremely hazardous c Welding on the tank in any manner will void the warranty
2. Never use an electric air compressor outdoors when it is raining or on a wet surface, as it many cause an
electrical shock.
3. This unit starts automa cally. ALWAYS shut of the compressor,
Remove the plug from the outlet. And bleed all pressure from the
2
should also take into account the when the tool is
such as: maintain
work pa erns.
rovide a longer and safer service life for your air compressor.
improving and perfec g the exis g products. Therefore,
ave this manual.
shipping plug inserted into the Oil Filler
If it is necessary to
is operated by turning the Regulator
ng the Compressor. Use nylon thread-seal tape when
If sparks come into
GB
system before servicing the compressor, and when the compressor is not in use.
4. Check the manufacturer's maximum pressure ra
pressure must be regulated so as to never exceed the maximum pressure ra
5. High temperatures and moving parts are present under the shroud. To prevent burns or other injuries.
DO NOT operate with
the shroud removed. Allow the compressor parts to cool before handling or servicing.
6. Be certain to read all labels when you are sparying paints or toxic materials, and follow the safety
instruc
ins
7. Always wear safety goggles or glasses when using an air Compressor. Never point any nozzle or sprayer
toward a person or any part of the body.
8. Do not adjust the pressure switch or relief valve for any reason. Doing so voids all warran
been pre-set at the factory for the maximum pressure of this unit.
our apology

SAFETY INSTRUCTION

MODERATE INJURY OR DAMAGE TO EQUIPMENT.
1. Drain the moisture from the tank on a daily basis. A clean, dry tank will help prevent corrosion.
2. Pull the pressure relief valve ring daily to ensure that the valve Is
valve of any possible Obs
3. To provide proper ven a
from the nearest wall, in a well-ven ated area.
4. Fasten the compressor down securely if transpo
tank before tr
5. Protect the air hose and electric cord from damage and puncture. Inspect them weekly for weak or worn
spots, and replace if necessary.
WARNING!
DISCONNECT POWER AND RELE ASE ALL PRESSURE FROM THE SYSTEM BEFORE ATTEMPTING TO
INSTALL,SERVICE, RELOCATE OR PERFORM ANY MAINANCE.
1. Follow all local eletrical and safety codes as well as Na
and Health Act(OSHA).
2. Electria motors and starters must be securety and adequately grounded using a three-pronged Outlet.
CAUTION!
Never use an extension cord with this product.
power loss and permanent motor damage. Use of and extension cord voids the warranty.
Record the Model No.,Serial No. and Date of Purchase in the sapce below.
Model No.
Serial No.
Date of Purchase
Retain these numbers for future reference
3. BRIEF DESCRIPTION
This micro air compressor is of novel design excellent workmanship. Having the
cons
in machinery, chemical industry, spray and dec
compressed air is required.
for air tools and accessories. Compressor outlet
Use a respirator mask if there is a chance of inhaling anything you are spraying. Read all
re that your respirator mask will protect you.
for cooling, the compressor must be kept a miniumum of 31cm(12 inches)
is necessary. Pressure must be released from the
rance, light weight, easy opera
ora toma
GB
tool.
They have
properly, and to clear the
etrical Codes(NEC) and Occupa afety
air hose instead of an extension cord to avoid
Advantages of compact
fety and low noise, it can be widely used
control system and other fields where
3