Leviton 3059-01Y Manual De Instrucciones

WARNINGS AND CAUTIONS:
• TO AVOID FIRE, SHOCK OR DEATH; UNPLUG CORD and TURN OFF POWER at circuit
breaker or fuse and test that power is off before installing, removing or servicing device!
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• Use these devices with copper or copper-clad wire only.
NOTE: Use chart below to identify the 1 Gang Box
needed for your application:
LEVITON 1 GANG POWER BOXES
Dimension (inches)
Description Catalog no. Color
A B C
1 Gang Standard 3059-01Y Yellow
3.375 3.900 2.500
(for 0.23 - 0.542 Cable) 3059-01E Black
1 Gang Std. Feed Through 3059F-01Y Yellow
3.375 3.900 2.500
(for 0.23 - 0.542 Cable) 3059F-01E Black
1 Gang Standard 3059-02Y Yellow
3.375 3.900 2.500
(for 0.59 - 1.00 Cable) 3059-02E Black
1 Gang Std. Feed Through 3059F-02Y Yellow
3.375 3.900 2.500
(for 0.59 - 1.00 Cable) 3059F-02E Black
1 Gang Deep 3099-01Y Yellow
4.375 3.900 2.500
(for 0.23 - 0.542 Cable) 3099-01E Black
1 Gang Deep Feed Through 3099F-01Y Yellow
4.375 3.900 2.500
(for 0.23 - 0.542 Cable) 3099F-01E Black
1 Gang Deep 3099-02Y Yellow
4.375 3.900 2.500
(for 0.59 - 1.00 Cable) 3099-02E Black
1 Gang Deep Feed Through 3099F-02Y Yellow
4.375 3.900 2.500
(for 0.59 - 1.00 Cable)
3099F-02E Black
Receptacle Mounting to 1 Gang Rubber Box
1. Select appropriate cover for receptacle per chart below.
2. For Wet Locations Only: Remove the appropriate perforated cut-outs from the
gasket, remove film, and affix to back of cover. Refer to diagram 2.
3. Remove strap mounting screws from receptacle and discard. For a Duplex device
trim the mounting strap by removing the 4 "ears". For a Decora ® device remove the
"4" ears and "2" center tabs as shown in diagram 3.
4. Place wired receptacle in the mounting position as shown in diagram 4.
5. Use mounting screws provided to fasten cover and receptacle to rubber box. DO
NOT overtighten mounting screws. Ensure that cover is flush to rubber box.
NOTE: For a heavy duty installation, drill out (4) start holes located at corners on back of
covers. Fasten cover to rubber box using (6) mounting screws provided.
NOTE: Tamper Resistant GFCI receptacles are not compatible with Decora
For GFCI receptacle applications, use 1 gang deep box only.
LEVITON 1 GANG POWER BOX COVERS
1
Blank Decora
Cat. no. 3054 Cat. no. 3060
Duplex 1.39 dia. opening
Cat. no. 3051 Cat. no. 3052
Duplex flip lid 1.56 dia. opening
Cat. no. 3056 Cat. no. 3055
Single and Double Gang Box Wiring Instructions
WARNING: TO AVOID FIRE, SHOCK OR DEATH; UNPLUG CORD and TURN OFF POWER at circuit breaker or fuse and test that power is off before installing, removing or servicing device!
1. Install Cable Strain Relief Bushing(s) onto rubber box and torque Lock nut as follows: 1/2" NPT and 1" NPT torque 45-55 in-lbs.
2. Remove Tightening nut from bushing.
3. Strip no less than 6" of the cord cable jacket. DO NOT cut wire insulation.
4. Feed stripped length of cord through Tightening nut and bushing.
5. Torque Tightening nut as follows: 1/2" NPT and 1" NPT torque 45-55 in-lbs.
6. Strip conductors and install receptacle per installation instructions provided with receptacle.
NOTE: For feed-through requirements, install Cable Strain Relief Bushings on both sides of box as described above and splice conductors as per code requirements.
C
Lock nut/Contre-écrou/Tuerca de fijación
B
Strain relief bushing
Manchon détendeur
Buje del protector
A
contra tirones
Tightening nut
Écrou de serrage
Tuerca de ajuste
Receptacle cover
2
Couvercle de prise
Cubierta de receptáculo
Side with adhesive/Côté adhésif
Lado con el adhesivo
Cover gasket
Joint d'étanchéité
Empaquetadura
de la cubierta
Perforated areas
Zones perforées
Areas perforadas
For 1 gang single receptacle cover For 1 gang duplex and Decora
Couvercle pour une prise simple Couvercle pour une prise Decora
Cubierta para receptáculo de una unidad Cubierta Doble o Decora
Center tab
3 4
Patte centrale
Pestaña del centro
® flip lids.
Strap "ears"
Oeillets de la bride
Orejas de la ménsula
Optional Installation using Wire Mesh Strain Relief Grips
Autre type d'installation utilisant des filets détendeurs
Instalación Opcional usando Agarraderas Protectoras de Malla de Alambre
Decora flip lid
Cat. no. 3061
Lock Nut/Contre-écrou
Cable
Power Box
Câble
Boîte d'alimentation
Cable
Caja de Energía
1.39 dia. opening
flip lid
Cat. no. 3057
Compression Nut Mesh Grommet Cable Grip Body
Écrou flottant Filet Bague Corps du manchon
1.56 dia. opening
Tuerca de compresión Malla Ojal Cuerpo de agarradera
flip lid
de cable
Cat. no. 3058
TEMPORARY POWER BOX
Installation Instructions
Lock nut/Contre-écrou/Tuerca de fijación
Strain relief bushing
Manchon détendeur
Buje del protector
contra tirones
Tightening nut
Box Écrou de serrage
Tuerca de ajuste
Boîte
Caja
Duplex or Decora ® cover Receptacle cover
Couvercle double ou Decora MD Couvercle de prise
Cubierta Doble o Decora ® Cubierta de receptáculo
Side with adhesive/Côté adhésif
® cover For 2 gang single receptacle cover
MD ou double Couvercle pour une prise à deux dispositifs
® para una unidad Cubierta para receptáculo de dos
3
Cover
mounting screw
Vis de montage du
couvercle
Tornillo de
montaje de la
Device
cubierta
mounting
screw
Vis de montage
du dispositif
Tornillo
de montaje
1. Slide compression nut over cable. Compress mesh and slide over cable. Slide grommet over cable.
2. Secure cable grip body to power box using lock nut. Torque 45-55 in-lbs for 1/2" NPT and 1" NPT.
3. Slide grommet into cable grip body and lay mesh flat against grommet. NOTE: Cable jacket may have to be
stripped to pass through body. Ensure jacket is completely covered by grommet when assembled.
4. Tighten compression nut onto cable grip body. Smooth mesh onto cable eliminating slack.
Tuerca de
Seguridad
1. Glisser l'écrou flottant, le filet comprimé et la bague sur le câble.
2. Fixer le corps du manchon sur la boîte d'alimentation en serrant le contre-écrou à un couple de 45-55 po-lb (filetage NPT de 1 ou de 1/2 po).
3. Glisser la bague dans le corps du manchon et poser l'extrémité du filet contre la bague.
REMARQUE : il pourrait être nécessaire de dégainer le câble pour permettre le passage dans le corps.
On doit s'assurer que la gaine est entièrement couverte par la bague une fois l'assemblage terminé.
4. Serrer l'écrou flottant sur le corps du manchon. Tendre le filet le long du câble en aplatissant tous les plis.
1. Deslice la tuerca de compresión sobre el cable. Comprima la malla y deslícela sobre el cable. Deslice la arandela sobre el cable.
2. Asegure el cuerpo de la agarradera de cable a la caja de alimentación usando la tuerca de seguridad. Use una presión de 45 a 55
in-lbs para tuercas NPT de 12.7 mm (1/2") y NPT de 25.4 (1').
3. Deslice la arandela en el cuerpo de la agarradera del cable y que la malla quede plana contra el ojal. NOTA: El forro del cable debe
estar pelado para pasar a través del cuerpo. Asegure que el forro esté totalmente cubierto por la arandela cuando ensamble.
4. Apriete la tuerca de compresión sobre el cuerpo de la agarradera del cable. Alise la malla eliminando el cable flojo.
B
Box
Boîte
Caja
Duplex or Decora ® cover
2
Receptacle Mounting to 2 Gang Rubber Box
Couvercle double ou Decora MD
Cubierta Doble o Decora ®
1. Select appropriate cover for receptacle per chart below.
2. For Wet Locations Only: Remove the appropriate perforated cut-outs from the
gasket, remove film, and affix to back of cover. Refer to diagram 2.
Lado con el adhesivo
3. Mount wired receptacle to cover as shown in diagram 3, using mounting screws
provided. NOTE: For Decora
mount device to cover.
Cover gasket
4. Place cover/receptacle assembly onto rubber box in position as shown in diagram.
Joint d'étanchéité
Use (6) mounting screws provided to fasten cover assembly to rubber box. DO NOT
Empaquetadura
de la cubierta overtighten mounting screws. After tightening mounting screws, ensure that cover is
flush to rubber box.
Perforated areas
NOTE: Tamper Resistant GFCI receptacles are not compatible with Decora
Zones perforées
Areas perforadas
For 2 gang duplex and Decora ® cover
Couvercle pour une prise Decora MD ou double
Cubierta Doble o Decora ® para una unidad
Cover mounting screw
Vis de montage
du couvercle
Tornillo de montaje
4
de la cubierta
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in
writing at Leviton Manufacturing of Canada ULC to the attention of the Quality Assurance
Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone
at 1 800 405-5320.
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that
this product at the time of its sale by Leviton is free of defects in materials and workmanship
under normal and proper use for two years from the purchase date. Leviton's only obligation
is to correct such defects by repair or replacement, at its option. For details visit www.
leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability
for labor for removal of this product or reinstallation. This warranty is void if this product is
installed improperly or in an improper environment, overloaded, misused, opened, abused, or
altered in any manner, or is not used under normal operating conditions or not in accordance
with any labels or instructions. There are no other or implied warranties of any kind,
including merchantability and fitness for a particular purpose, but if any implied
warranty is required by the applicable jurisdiction, the duration of any such implied warranty,
including merchantability and fitness for a particular purpose, is limited to two years. Leviton
is not liable for incidental, indirect, special, or consequential damages, including
without limitation, damage to, or loss of use of, any equipment, lost sales or profits
or delay or failure to perform this warranty obligation. The remedies provided herein are
the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
PK-93660-10-02-0E
NOTE: Use chart below to identify the 2 Gang Box needed for
your application:
LEVITON 2 GANG POWER BOXES
Dimension (inches)
Description Catalog no. Color
A B
2 Gang Standard 3200-01Y Yellow
5.100 5.655
C (for 0.23 - 0.542 Cable) 3200-01E Black
2 Gang Std. Feed Through 3200F-01Y Yellow
5.100 5.655
(for 0.23 - 0.542 Cable) 3200F-01E Black
2 Gang Angled 3300-01Y Yellow
4.220 5.655
(for 0.23 - 0.542 Cable) 3300-01E Black
A
2 Gang Angled 3300-02Y Yellow
4.220 5.655
(for 0.59 - 1.00 Cable) 3300-02E Black
2 Gang Standard 3200-02Y Yellow
5.100 5.655
(for 0.59 - 1.00 Cable) 3200-02E Black
2 Gang Std. Feed Through 3200F-02Y Yellow
5.100 5.655
(for 0.59 - 1.00 Cable) 3200F-02E Black
devices, use provided mounting screws with nuts and
®
flip lids.
®
LEVITON 2 GANG POWER BOX COVERS
1
(2) Blank (2) Duplex
Cat. no. 3265 Cat. no. 3260
(1) 1.56 dia.
opening flip lid
(1) 1.56 dia. (1) 1.56 dia.
(1) Duplex flip lid
opening opening Cat. no. 3262W
(1) Duplex (1) Blank
Cat. no. 3262 Cat. no. 3261
(1) 1.56 dia.
(2) Decora (1) Blank, opening flip lid,
flip lid (1) Decora (1) Blank
Cat. no. 3251W Cat. no. 3261W
flip lid
Cat. no. 3241W
(2) Decora (1) Blank,
Cat. no. 3251 (2) 1.56 dia.
(1) Decora
Cat. no. 3241 opening flip lid
Cat. no. 3263W
(2) 1.56 dia. (2) Duplex
opening flip lid
Cat. no. 3263 Cat. no. 3260W
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
For Technical Assistance Call: 1-800-824-3005 (USA Only) or
1-800-405-5320 (Canada Only) www.leviton.com
C
4.655
4.655
4.655
4.655
4.655
4.655