System Setup - CROSSTEX Accutron ClearView RFS Instrucciones De Uso

System Setup

ClearView ™ RFS ™ Scavenging Circuits (43004, 43006)
1. Assemble the circuits per Figure 1 and install the mask on the circuit per Figure 2.
2. Connect the reservoir bag and hoses per Figure 3 for RFS Circuits or Figure 5 for Accu-vac
Caution: The bag must be on the downspout, only one vacuum controller can be used at one time (RFS Circuits or Accu-vac Circuits).
3. Adjust the flow on the RFS Circuit using knob
that it be checked periodically during the procedure as facility vacuum pressure can change from time to time.
4. Place mask on patient per Figure 6.
5. Adjust the flow on Accu-vac Circuit using knob
red=blocked flow (check for kinked hose).
ClearView Inline Circuits (43003, 43005)
™
1. Assemble the circuits per Figure 7 and install the mask on the circuit per Figure 8.
2. Connect the reservoir bag and corrugated hose per Figure 9.
Caution: The bag must be on the downspout, only one vacuum controller
3. Place mask on patient per Figure 6.
4. Connect the vacuum line to the vacuum source such as the chair
fitting T per Figure 11 after cutting off
5. Adjust the flow on the controller
down after initial setting although it is recommended that it be checked periodically during the procedure as facility vacuum pressure
can change from time to time.
Gas Flow Operation
Digital Ultra™ Flowmeters:
match the breathing rate of the patient by watching the reservoir bag. At the proper flow it will neither inflate to the max or
deflate to the minimum. Gradually increase %N
to avoid negative patient reactions. At end of procedure, reduce %N
stream.
Turn the unit on and adjust the Total Flow to match the breathing rate of the patient by watching the
Ultra PC™ Flowmeters:
reservoir bag. At the proper flow it will neither inflate to the max or deflate to the minimum. Gradually increase %N
desired effect is reached. Note that the Oxygen level will need to be reduced by the amount of increase in N
correct flow rate. Use the Titration method when adding N
%N O to 0 and increase O
2
stream.
Turn unit on. O
Ultra DC™ Flowmeters:
patient by watching the reservoir bag. At the proper flow it will neither inflate to the max or deflate to the minimum. Gradually
increase N O until desired effect is reached. Oxygen flow will need to be decreased by the same amount of the N
2
to maintain the proper Total Flow. Use the Titration method when adding N
of the procedure, reduce N
increased by the amount of N
ClearView Circuits can be reprocessed per 26613-INT. Do not exceed recommended temperatures.
™
UDI Product Tag included for product traceability purposes.
so that the needle is in the green zone of gauge
M
so that the light
W
Q .
per Figure 12 using knob
N
Turn on the unit. It should start at TOTAL FLOW of 5 lpm with 0 %N
O until desired effect is reached. Use the Titration method when adding N
2
flow by same amount to maintain proper flow. Run for 5 minutes to Flush N
2
flow should start at 3 lpm. Adjust Oxygen flow to match the breathing rate of the
2
O to 0 for five minutes to flush N
2
O decrease to maintain the same Total Flow.
2
K is green, blue=low flow (check vacuum flow from pump),
N can be used at one time.
per Figure 10 using installed fitting
V
so that the needle is in the green zone of gauge
R
O to 0 for five minutes to flush N
2
O to avoid negative patient reactions. At end of procedure, reduce
2
O to avoid negative patient reactions. At the end
2
O from patient's blood stream. The oxygen flow will have to be
2
Circuits.
™
L per Figure 4. It is recommended
Q or connect to wall outlet using
. Gauge can be laid
S
O. Adjust TOTAL FLOW to
2
O from patient's blood
2
O to maintain the
2
O from patient's blood
2
EN
O
2
O until
2
O increase
2