Safety Instructions - Deltaco Gaming GAM-133 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 15
ENG
1.
Headset
2.
Power on/off button and LEDs on/off
3.
Equalizer button
4.
USB-C charge port
5.
Microphone mute button
6.
Volume adjustment wheel
7.
Microphone port
8.
Microphone
9.
USB receiver
10.
USB-A to USB-C charge cable
11.
3.5 mm audio cable
On/off
Press and hold the power button for 2 seconds
to power the headset on. Press and hold for 4
seconds to power it off.
Microphone
The microphone is detachable.
Press the microphone mute button to turn it on or off.
Insert the microphone by matching the lock icon with the
notch. Then turn the microphone counterclockwise to lock
it in place. To detach the microphone, turn it to unlock
it, and pull it out.
Volume
Use the volume wheel to adjust volume.
LEDs
Short press the on/off button to change LED mode.
Automatic mode (RGB) > static red > static greenish blue >
static purple > static yellow > static teal > static white
> light off.
Equalizer
Press the equalizer button to change between modes: Hifi,
bass, 3D. The headset remembers last used mode after being
turned off and turned on again.
Connect wirelessly
1. Connect the USB receiver to your computer or device.
2. Power the headset on.
3. The LED powers on to confirm power on status.
4. Pairing: Press and hold the power button for about 5
seconds to pair or re-pair.
If the headset has already been paired, then you skip the
pairing step. It can also be used as a troubleshooting
step.
5. If the LEDs changes to automatic mode (RGB), then the
connection was successful.
If the LEDs are flashing green, then the connection failed.
If it failed, please try disconnecting and connecting
again.It is possible to have 2 headsets connected to 1
USB receiver. But it is not possible to connect 2 USB
receivers to 1 headset. In the settings of your computer
or device, make sure you have set the audio output
correctly. If you are also using the microphone, please
set the audio input correctly. If you move out of range
the headset will flash green. When you move in range
again, the headset will automatically reconnect. If you
disconnect the USB receiver, the headset will flash green.
Flashing green = currently not paired.
Wired connection
To use 3.5 mm connection, you need to first turn the
headset off (if it was on).
Use the including 3.5 mm audio cable to connect the
headset to your device. The headset will activate wired
mode automatically.
When using the 3.5 mm connection, the LEDs and the
equalizer will be temporally disabled.
Charging
You can use the headset while it is charging.
Connect the USB cable to the headset and a USB power
adapter (5V/1A) to charge it. When the battery has less
then 10% left, the headset will play a tone 5 times.
The headset turns off automatically after 30 minutes
of inactivity, and after 10 minutes if it has not been
paired.
Charging takes about 3 hours.
Flashing red = Charging.
Green = Fully charged.
Compatibility
Compatibility: PC | Mac | PS5 | Xbox One (wired only) |
Mobile (wired only)
Microphone mute function is disabled while in wired mode
(3.5 mm).
Microphone mute function in wireless mode (USB receiver)
is compatible with PC, PlayStation 4/5 and Mac.
Cleaning
Clean the product by using a dry cloth.

Safety instructions

1. Keep the product dry. Keep it away from all liquids.
This product is not waterproof.
2. Do not open up or try to repair the product by
yourself.
3. Keep the product and packaging out of reach of children
to prevent accidents and chocking hazards.
4. Do not drop or expose to shock damage.
Warranty
Please, see www.deltaco.eu for warranty information.
Support
More product information can be found at www.deltaco.eu.
Contact us by e-mail: help@deltaco.eu.
3

Publicidad

Tabla de contenido
loading

Tabla de contenido