Power Stroke PSL0BA121 Manual De Instrucciones

12 V LITHIUM-ION BATTERY PACK
PSL0BA121
Use this battery pack for PowerStroke 12 V Lithium-ion
cordless products only. Refer to the Operator's Manual
provided with product. Always mention the appropriate
model number when communicating with us regarding
your battery pack.
GENERAL SAFETY RULES GENERAL SAFETY RULES
WARNING!
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
 Battery tools do not have to be plugged into
an electrical outlet; therefore, they are always
in operating condition. Be aware of possible
hazards when not using your battery tool or
when changing accessories. Following this
rule will reduce the risk of electric shock, fire, or
serious personal injury.
 Do not place battery tools or their batteries near
fire or heat. This will reduce the risk of explosion
and possibly injury.
 Do not crush, drop or damage battery pack. Do
not use a battery pack or charger that has been
dropped or received a sharp blow. A damaged
battery is subject to explosion. Properly dispose of
a dropped or damaged battery immediately.
 Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk
of serious personal injury, never use any cordless
product in the presence of open flame. An exploded
battery can propel debris and chemicals. If exposed,
flush with water immediately.
 Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
 For use only with PowerStroke 12 V lithium-ion
charger, model number PSL0CH121.
 For best results, your battery tool should be
charged in a location where the temperature is
more than 50°F but less than
risk of serious personal injury, do not store outside
or in vehicles.
 Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in con-
tact with your skin, wash immediately with soap
and water. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule
will reduce the risk of serious personal injury.
 When battery pack is not in use, keep it away
from other metal objects like: paper clips, coins,
keys, nails, screws, or other small metal objects
100°F. To reduce the
English
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause sparks, burns, or a fire.
 Always remove battery pack from your tool when
you are assembling parts, making adjustments,
cleaning, or when not in use. Removing battery
pack will prevent accidental starting that could cause
serious personal injury.
 Always remove battery pack before storing the
device.
 When battery becomes fully charged, unplug the
charger from the power supply and remove the
battery pack from the charger.
 Always wear eye protection with side shields
marked to comply with ANSI Z87.1. Failure to do
so could result in objects being thrown into your
eyes and other possible serious injuries.
 Keep battery pack dry, clean, and free from oil
and grease. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based
products, or any solvents to clean battery pack.
 Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also.
OPERATION
OPERATION
POWERSTROKE LITHIUM-ION BATTERY
PACKS
Lithium-ion batteries deliver fade free power for their
entire run time. 12 V lithium-ion tools will not gradually
lose power due to decreasing battery charge. Instead,
power from the battery pack will drop from full to zero
once the full charge has been drained from the battery.
Once this happens, recharging of the battery is required.
It is not necessary to drain the battery pack completely
before recharging.
BATTERY PROTECTION FEATURES
PowerStroke 12 V lithium-ion battery packs are designed
with features that protect the lithium-ion cells and maxi-
mize battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
COLD WEATHER OPERATION
The lithium-ion battery pack can be used in tempera-
tures down to -4°F. Put the battery pack on a tool and
use the tool in a light duty application. After about a
minute, the pack will warm up and begin operating
normally.
CHARGING THE BATTERY PACK
See Figure 1.
Battery packs are shipped in a low charge condition to
prevent possible problems. Therefore, you should charge
prior to first use. If the charger does not charge the bat-
tery pack under normal circumstances, return both the
battery pack and charger to your nearest Authorized
Service Center for electrical check.