Important - Skil 2120 Manual De Instrucciones

in the cord of the charger to the earth terminal of the plug
§
If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left
unattended.
Before Putting into Operation
BATTERY CHARGING (figure 6)
Battery of new tools is not fully charged.
A battery that is new or has not been used for a longer
period does not develop its full capacity until after
approximately 5 charging/discharging cycles.
Plug the output cord of the charger K into the socket in the
bottom of the screwdriver handle as shown in figure 3. Plug
the charger L into any standard electrical outlet.
.
Only the charger F000608072 has the selective key M
for input voltage. Always be certain that voltage selection in
the key is appropriate for your power source voltage.
.
Unplug the charger from the tool after charging
period has ended thereby lengthening the service life
of the battery.

IMPORTANT:

While charging, the charger and the battery may become
warm to touch; this is normal and does not indicate a
problem.
Do not charge at temperatures below 0° C and over 40° C.
When you charge the battery for the first time, it only
accepts 80% of its maximum capacity; after several
charges and discharges, however, the batteries should be
at full capacity and deliver maximum performance
Do not repeatedly recharge the battery after only a few
minutes of operation; this may result in a reduction of
operating time and battery efficiency.
The nickel-cadmium/nickel-manganese battery must be
kept separate from the natural environment and should not
be disposed of as normal domestic waste.
.
? Prior to disposal protect battery terminals with
heavy tape to prevent short-circuit.
If you anticipate long periods of non-use for the tool, it is
best to unplug the charger from its power source.
LOADING STAPLES/NAILS
Turn tool upside down (figure 4).
Press lever B while pulling slider C backwards.
Insert the staple/nail strip into magazine D with legs facing
upward (maximal capacity 70 staples/nails).
Push slider C against tacker head E until it snaplocks.
When inserting a nail strip (not supplied with the tool) tilt the
tool in such a way, that the nail strip rests against the
magazine side which corresponds with the nail symbol on
tacker head E (figure 5).
Operating the tool
Firmly press tacker head E against the workpiece until it is
pushed in a few millimeters (figure 6).
Green light F will turn on indicating that the tool is ready to
staple briefly press switch G and then release again.
Switch G is locked as long as you do not press tacker head
E against the workpiece and green light F does not turn on,
thus preventing accidental operation.
Remove all staples/nails from the magazine after
each use
All manuals and user guides at all-guides.com
Impact control
With wheel H the required impact level can be selected in
steps (figure 7).
Indicator I shows the selected impact level:
- "Min." for thin and light materials such as foils and Fabrics;
- "Max." for thick and tough materials such as hard woods
Before starting a job, find the optimal impact level by testing
out on spare material.
.
order to relieve the tension spring
EXTRA STAPLE STORAGE (figure 8)
Aplication advice
Fastening panels (figure 9).
Do not use the tool for fastening ceiling panelling on profiled
wood or grooves.
Fixing textiles (figure 10).
Avoid blank shots in order to reduce the wear of the impact
strike.
Maintenance
§
For safe and proper working, always keep the machine, the
ventilation and charger slots clean.
§
§
If the machine should fail despite the rigorous
manufacturing and testing procedures, repair should be
carried out by an authorized customer services center for
SKIL Power Tools
Guarantee
We guarantee SKIL appliances in accordance with
Statutory/country-specific regulations (proof of purchase by
invoice or delivery note).
Damage attributable to normal wear and tear, overload or
improper handling will be excluded from the guarantee.
In case of complaint please send the machine,
undismantled, to your dealer or the SKIL Service Center
for Electric Power Tools.
Warning!
Freight and insurance costs are charged to the client, even
for warranty claims.
Environmental protection
Recycle raw materials instead of disposing as waste.
recycling.
The nickel-cadmium/nickel-manganese battery must be
kept separate from the natural environment and should not
be disposed of as normal domestic. Do not use tool or
charger when damaged; take it to one of the officially
registered SKIL Service Stations for a safety check.
15
and walls.
Set the impact level to "Min." after each use in
Unplug charger from power source before cleaning.
The charger may be cleaned most effectively with
compressed air (wear safety goggles).
Clean charging contacts in charger with alcohol or
contact cleaner.
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
The plastic components are labeled for categorized
Subject to change without notice