Before First Use - Adler europe AD 1345 Manual De Uso

20. Always use caution when boiling water in the kettle. Do not touch the housing of kettle
or lid. Do not open the lid during boiling in kettle or immediately after boiling, because
steam coming out of lid can cause burns.
21. Move the kettle only by holding it by handle..
22. Never fill kettle above MAX level and below MIN level. It may cause damage of kettle.
23. Never switch on kettle without water.
24. Never use kettle without filter or with open cover (automatic shutdown will not work).
25. Descale your kettle regularly. Using kettle with heating element covered by scale may
cause damage.
26. Do not use aggressive detergents to wash the kettle housing - they can damage the
kettle or remove the markings.
27. The device is not designed to work with external schedulers or separate remote control
system.
28. Do not wash the base of the kettle directly in the water, just wipe with a dry cloth.
29. Children aged 3 to 8 years old can enable and disable the device only when it is in its
normal position of use, they are supervised or instructed on the safe use and understand
the resulting risks. Children aged 3 to 8 years old can not connect device, operate, clean or
maintain.
DEVICE DESCRIPTION ELECTRIC KETTLE AD1345
1. Lid
2. LED display
3. Housing
4. Handle
5. Base
6. Cover opening button
7. Power button (On / Off)
8. Temperature selection button
9. Keep-warm function indicator
10. Cooking indicator
11. MIN / MAX water level indicator
12. Touch panel

BEFORE FIRST USE

Fill the kettle three times with water to the maximum level, boil, and pour out. To remove any factory odor.
Only touch the buttons on the touch panel (12) with your fingertips, touching your fingernails may damage the touch panel!
BASIC OPERATION:
SINGLE WATER BOLING UP TO 100 °C
1. Place the base (5) on a stable, flat, and heat-resistant surface.
2. Fill the kettle with water so that the water level is between the maximum and minimum level on the water level indicator inside the
kettle (11).
3. Remember to close the kettle with the lid (1) after filling, otherwise, the kettle will not turn off automatically after boiling water.
4. Insert the plug of the power cord into a 220-240V ~ 50-60Hz mains socket. Put the kettle on the base (5), you will hear the "di" sound,
and the LED display (2) will show the current water temperature.
5. Press the button (7), the cooking indicator (10) will light up, then the heater will start heating the water and the LED display (2) will start
showing the current water temperature. The temperature of the water will increase until it boils, i.e. up to 100 ° C.
6. After boiling the water, the kettle will automatically turn off, and you will hear a triple sound "di-di-di".
7. If you want to turn off the kettle before the boiling water is finished, lift it from the base (5) or press the button (7).
8. The kettle can be switched on again approximately 2 minutes after the last use.
9. When the appliance is not in use, the LED display (2) will stay on showing the current water temperature.
ADVANCED OPERATION:
BOILING WATER TO THE SELECTED TEMPERATURE 40 ℃ OR 55 ℃ / 80 ℃ / 90 ℃
WITH THE TEMPERATURE KEEP-WARM FUNCTION
Put the kettle on the stand (5), and wait until you hear the "di" sound. Press the temperature selection button (8), the LED display (2) will
show the temperature of your choice (40 ℃ or 55 ℃ / 80 ℃ / 90 ℃) and blink four times storing the selected temperature level, the
temperature hold function indicator (9) will light up. Then the LCD display (2) will show the current water temperature inside the kettle.
The kettle will stop boiling water when it reaches the selected temperature level of 40 ℃ or 55 ℃ / 80 ℃ / 90 ℃, you will hear a triple
sound "di-di-di". After reaching the set temperature, the kettle will switch to the temperature maintenance mode and will periodically heat
the water when the water temperature drops by 5 ℃ in relation to the selected temperature level.
If the water temperature in the kettle is higher than the desired temperature (more than 5 ℃), the indicator of the keep-warm function (9)
will flash until the water cools down to the pre-set temperature of 40 ℃ or 55 ℃ 80 ℃ / 90 ℃), being in the keep temperature mode all
the time.
In order to interrupt the temperature maintenance function, remove the kettle from its base (5) or press the button (7). The keep-warm
function is maintained for max.24 hours from the last cooking.
4