Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
1
EN
2
9.- CH 1 - CH 2: stereo line level and phono or auxiliary level inputs for channels CH 1 and CH 2. They
3
allow the connection of players with line level and phono or aux level output respectively, 2 x RCA
1
4
connectors. If you use the PHONO/AUX inputs, you must select the input type on the selector switch
before physically connecting the equipment.
2
3
10.- PHONO/AUX: selectors that allow you to choose the input type for the phono/aux connectors of
5
1
channels CH 1 and CH 2.
4
11.- GND: connection for equipment ground. If you connect several devices together, it is recommended to
2
use a common ground for all of them.
3
5
12.- MIC 1: balanced microphone input, XLR combo connector and 6.3 mm stereo jack.
4
13.- MIC 2, MIC 3: balanced microphone inputs, XLR connectors.
6
5
MENU (PLAYER, PC CONNECTION AND SETTINGS)
To access the menu, long press the MENU button on the player. To scroll through the menu options or
6
modify the values of the settings use the
This menu has the following options:
MUSIC: accesses the player of the connected USB or SD devices.
PC CONNECTION: allows you to play audio from the computer connected via USB cable
to the mixer's USB port. It will also grant access to the content of the SD card connected
to the mixer (play, delete and add files).
SYSTEM SETTINGS: allows you to view/change the following parameters: display
contrast (CONTRAST), menu language (LANGUAGE), firmware version (FIRMWARE
VERSION) and return to the menu screen (QUIT).
CONNECTION
- Before making any connections, make sure that all devices are switched off and disconnected from the
power supply.
- Check that all volume controls on the microphones, input channels CH 1 to CH 5, MASTER and BOOTH
outputs are set to minimum.
- Connect the desired equipment to the input channels. Connect players to the LINE inputs of channels
CH 1 to CH 5. And connect players with auxiliary line level output to the AUX inputs of channels CH 1 and
CH 2 and set the input level selector switch to the AUX position. If you want to connect a turntable, use
the PHONO inputs on channels CH 1 and CH 2 and set the input level selector to the PHONO position. If
your turntable has a ground connection, connect it to the GND terminal on the rear panel.
- Connect a USB device or SD memory card with MP3 files to the corresponding port of the player.
- Connect the balanced or unbalanced MASTER output to a line-level input of an amplifier or power stage.
If desired, you can connect the BOOTH output to self-amplified monitor speakers.
- Connect the devices to the power supply. Switch on the equipment in this order: peripheral equipment,
followed by the mixer SM-1860U and lastly the amplifier or power amplifier (if necessary).
- Adjust the volume of inputs MIC 1 to MIC 3 and CH 1 to CH 5; and select the output buses to which to
send each channel CH 1 to CH 5.
- Adjust the volume of the MASTER 1 and MASTER 2 outputs.
1
8
8
7
6
7
13
13
14
14
15 16
1
1
2
8
7
9
10
11
12
/
buttons and finally press MENU to validate.
13
14
15 16
15 16
3
- 4 -
10
9
11
10
12
11
12
4 5 6 7
17
18
17
MENU
18
320
ROCK
0001
MP3
1
0003
17
00:53/04:14
t r a c k 0 0 1 . m p 3
BOOTH
MENU
18
BOOTH
PHONES
19
19
20
10
8
0
t
1
Publicidad
Tabla de contenido
