Technical Specification - Rapid RX1000 Manual De Instrucciones

only original replacement parts. Damaged charg-
ers, cables and plugs increase the risk of electric
shock.
e) Do not operate the charger on an easily ignited
surface (e.g. paper, textiles, etc.) or in a flamma-
ble environment. There is a risk of fire due to the
charger heating up during operation.
f) Rechargeable batteries are to be removed from
the appliance before being charged.
7) SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorised service providers.
HOT AIR TOOL SAFETY
WARNING: This tool must be placed on its
stand when not in use.
A fire may result if the appliance is not used with
care, therefore
– be careful when using the appliance in places
where there are combustible materials;
– do not apply to the same place for a long time;
– do not use in presence of an explosive atmos-
phere;
– be aware that heat may be conducted to combus-
tible materials that are out of sight;
– place the appliance on its stand after use and
allow it to cool down before storage;
– do not leave the appliance unattended when it is
switched on.
– This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory and mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.

TECHNICAL SPECIFICATION

Tool Weight (bare-tool)
Dimensions (bare-tool)
Voltage
Temperature min
Temperature max
Airflow
Recommended Battery type Power for all 4.0 Ah, 6.0 Ah
Recommended Charger type Power for all AL1810CV, AL1830CV, AL18V-20
During charge
During usage
During storage
6
620 grams
169 x 71 x 208 L*W*H (mm)
18V
Setting 1 Setting 2
30°C 30°C
440°C 550°C
medium high
Permitted ambiant temperature
0°C to +35°C
0°C to +50°C
-20°C to +50°C
FEATURES
Power switch, fig 1A
Nozzle cap, fig 1B
Handle, Fig 1C
Accessories can be removed by rotating the nozzle
cap clockwise. Fig 2
Display, fig 3
Display, fig 3D, shows the actual temperature
Temperature can be adjusted by pressing +/- button
in 10°C increments. Fig 3E
Temperature will flash some seconds when target
temperature is reached
Maximum temperature vary from setting 1 and 2.
Setting 1 : medium airflow, maximum temperature
440°C
Setting 2 : high airflow, maximum temperature 550°C
Battery power indicator, fig 3F
LCD screen shows battery power indicator. The Battery cells is
divided in 5 slots.
5 slots means the level of charge is at its maximum.
This is an indication of approximate levels of charge remaining in
the battery pack.
Each slot will disappear time by time once the level of charge is
decreasing.
Once the battery is fully discharged, display will show a blinking
empty battery symbol.
BATTERY ERROR INDICATIONS
If an error in the battery is detected, the battery
indicator on the display (Figure 3.F) will instead of
residual capacity show the following indications, and
the tool will not operate.
Battery Error Indications
Error type Battery indicator (Figure 3.F)
Battery is too All slots are
warm or too flashing for 5sec
cold
Battery not First and last slots
recognized are flashing for
5sec
Power/Air flow LED indicator, fig 3G
Stand for vertical operation with free hands or stor-
age. Fig 4H
Battery Charging
Note: The battery supplied is partially charged. To
ensure full capacity of the battery, completely charge
the battery in the battery charger before using your
power tool for the first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
The lithium-ion battery is protected against deep dis-
charging by the "Electronic Cell Protection (ECP)".
When the battery is empty, the machine is switched
Solution
Allow the battery to reach
normal temperature
prior use
Use a recommended bat-
tery in section "Technical
specification"
The Arrows show level of airflow
Setting 1 : 2 arrows , medium airflow
Setting 2 : 3 arrows, high airflow