Bluetooth Mode - Sharp CP-SS30 Manual Del Usuario

6
Using your bookshelf speakers
Standby/ON
• When you fi rst connect the unit to the power socket, the unit will be in
STANDBY mode. The indicator will light up red.
• Press on the remote control to switch the speakers between ON and
standby.
• Disconnect the plug from the power wall socket if you want to switch
the unit off completely.
NOTE: The speakers will go into standby mode after 15 minutes of inactivity.
Select modes
Press the volume control on the unit to cycle through the source options,
or use the remote control to select the desired mode.
Red: Standby
Blue: Bluetooth
Green: Aux
Cyan: RCA
Yellow: Optical
Purple: USB
Adjust the volume
– Use the volume knob on the unit or
adjust the volume.
– To mute the sound, press on the remote control. To resume the sound,
press or +/– on the remote control, or rotate the volume control
on the unit.
– While adjusting the volume, the status indicator fl ashes quickly.
– When the volume level reaches its maximum level, if you press + again,
the indicator fl ashes once. When the volume level reaches its minimum
level, if you press – again, the LED indicator fl ashes once.
Equaliser (EQ) settings
You can adjust the sound of the bookshelf speakers using the equaliser
presets. Press on the remote control once to confi rm current EQ mode.
Continue pressing to cycle through the EQ presets.
• Classic - Green LED indicator fl ashes for 2 seconds
• POP -Yellow LED indicator fl ashes for 2 seconds
• Rock - Blue LED indicator fl ashes for 2 seconds
• Movie - Purple LED indicator fl ashes for 2 seconds
• Voice - Cyan LED indicator fl ashes for 2 seconds
• Custom - White LED indicator fl ashes for 2 seconds
Custom settings
• Press the button to enter Custom settings or press either the BASS
or TREB button +/- buttons once, a white light will fl ash for 2 seconds.
• Use the BASS/TREB buttons on the remote control to increase (+) or
decrease (-) the EQ level. The selected EQ level is indicated by the speed
at which the LED indicator on the speaker fl ashes. A fl ashing red LED
indicates an increased level, a white LED (not fl ashing) indicates the
level is fl at/0, a fl ashing green LED indicates a decreased level.
LED colour EQ level
+3
RED +2
+1
White 0
-1
Green -2
-3
NOTE: New EQ changes are saved as default. You have 3 seconds between
each key press to make any changes before the EQ mode exits.
+/– on the remote control to
Speed LED fl ashing
Fast
Medium
Slow
On
Slow
Medium
Fast
AUX/OPTICAL/RCA
1. Ensure that the unit is connected to the TV or audio device.
2. While the unit is powered on, ensure the correct source is selected
either using the remote control or by pressing the volume control
on the unit.
3. Operate your audio device directly for playback features.
4. Use the volume control on the unit or
to adjust the volume level.
NOTE: Please ensure RCA and AUX input are set to mininum
50% volume on the source device. Volume can be adjusted via
the speaker, the remote control or the source device.

Bluetooth mode

Pair Bluetooth-enabled devices
The fi rst time you connect your Bluetooth device to these speakers, you
need to pair your device to these speakers.
NOTE:
– The operational range between these speakers and a Bluetooth device
is approximately 8 meters (without any object between the Bluetooth
device and the unit).
– Before you connect a Bluetooth device to these speakers, ensure you
know the device's capabilities.
– Compatibility with all Bluetooth devices is not guaranteed.
– Any obstacle between these speakers and a Bluetooth device can
reduce the operational range.
– If the signal strength is weak, your Bluetooth receiver may disconnect,
but it will re-enter pairing mode automatically.
1. With the unit powered on, press on the remote control or press the
volume control on the unit to select Bluetooth mode. The indicator
light will fl ash blue.
2. Activate your Bluetooth device and select the search mode.
"SHARP CP-SS30" will appear on your Bluetooth device list.
– If you cannot fi nd the unit, press and hold on the remote control.
3. Select "SHARP CP-SS30" from the list of devices. An audio prompt will
sound when it has been successfully connected, and the indicator will
light a solid blue.
4. Begin playing music from the connected Bluetooth device.
To disconnect the Bluetooth function, you can:
– Switch to another function on the unit.
– Disable the Bluetooth function on your device. An audio prompt will
sound when it has been successfully disconnected.
– Press and hold on the remote control.
TIPS:
• Enter "0000" for the password if necessary.
• If no other Bluetooth device pairs with the speakers in 2 minutes, the
speakers will reconnect to the previous connection.
• The speakers will also be disconnected when your device is moved
beyond the operational range.
• If you want to reconnect your device to this speakers, place it within the
operational range.
• If the device is moved beyond the operational range, when it is brought
back, please check if the device is still connected to the speakers.
• If the connection is lost, follow the instructions above to pair your
device to the speakers again.
Listen to music from Bluetooth device
– If the connected Bluetooth device supports Advanced Audio
Distribution Profi le (A2DP), you can listen to the music stored on the
device through the speakers.
+/– on the remote control