Silentaire 558101120 Guía De Uso Y Cuidado

NOTE: Keep your receipt and these instructions for proof of purchase.
NOTE: Dispose used products according to local regulation.
WArNING: Shut off the power at the circuit breaker or fuse panel before removing
the old fixture, ballast, or fluorescent tubes.
If you are unfamiliar with electrical installations, we recommend you contact
a qualified electrician to do the installation.
NOTE: Two people are recommended for installation of this light fixture.
NOTE: MOUNT THIS EQUIPMENT AT LEAST 2.3 M ABOVE THE FLOOR.
It is the Installer's responsibility to verify safe ozone concentrations by taking into
account the number of products in a given volume of space, the characteristics of the
ventilation system, access, and other factors.
HArDWAre AVAILABLe TO PUrcHASe
Hardware kits for surface mounting and suspension mounting are sold as separate accessories. Please contact ETi SSL Customer Service 1-855-384-7754 for additional information.
Part Description
AA Aircraft Cable for Suspension Mounting
INSTALLATION
NOTICE: Select a suitable location that can support the weight of the fixture.
Determine the method of mounting before beginning installation.
CAUTION: Installer is responsible to ensure grid location is rated for fixture weight
prior to installation. If uncertain, use cable to support fixture from the retention clips
to a suitable support structure. Failure to do so can cause serious injury.
1
Open the package and remove the EPE foam, then take out the UVC lamps.
2
Slightly press the small cover with finger, and remove the screw with the
screwdriver, then open the small cover.
3
Keep the small cover at 90 degree to the front panel, press the other side of the front
panel at position C with the thumbs. And pull the back the small cover at position D
with index finger to pull out the front panel.
4
When you open the front panel, unplug the ground wire at position A, and then remove
the safety rope at position B.
5
Hold the white plastic head by the thumbs and index fingers, insert two UVC lamps
to the lamp holder, and snap the glass tube into the metal clip, and check if tighten.
The marking line on the UVC lamps should be parallel to the end of the lamp holder.
Note that the end of the UVC lamp should not touch the other internal components of
the fixture. Immediately open the window if the UVC lamps are broken accidentally.
Dispose of broken UVC lamps according to the local environmental protection
agency.
6
Install the safety rope and the front panel, then connect the ground wire. Open
the small cover and keep it at 90 degree to the fixture surface. Install the front
panel to the fixture and check tightness, use the screw to lock the small cover
by screwdriver.
7
Shut off power at the electrical panel before beginning the installation.
8
Remove existing fixture and set aside to recycle in accordance with local requirements.
MAkINg eLecTrIcAL cONNecTIONS
9
Remove the driver box cover plate and punch out the knock out hole.
10
Feed the conduit or Romex (based on local electrical code) through the knock out hole.
NOTE: It's recommended to use 16GA pigtails from the terminal block to the respective power supply wires. Must add pigtail or jumper wires into the ACL and ACN terminal
to use a wire larger than 16AWG for both AC and Neutral Line.
11
Make the electrical connections: Connect black (L) wire with black wire in the driver. Connect white (N) wire with white wire in the driver. Connect ground wire with green
wire in the driver. If a 0-10v dimming circuit is available, connect fixture purple wire to driver DIM+ and pink fixture wire to driver DIM-.
12
Tuck wires inside the driver box and reattach the driver cover.
grID ceILINg INSTALLATION
Bend each of the mounting clips on the back of the fixture upward and then twist the top 90°. Place the fixture into
13a
the ceiling grid, hook the mounting clips over the grid ceiling supports and make sure it is secure.
USE AND CArE GUIDE
2X2 UVC PLASMA FLAT PANEL
Quantity Part #
2 95457326101
PAckAge cONTeNTS
Part Description Quantity
A Fixture 1
B UVC lamps 2
C Wire Connector 5
B
x 2
Step1:
Step3:
C
D
Step4:
B
A
B
A
Step5:
Model # 558101120
Part # SAFP-22-LB4-8-CP4-MV-LVD
C
AA
Step2:
A
F