Publicidad
Idiomas disponibles
Idiomas disponibles
Instructions for use and safety
1
General view:
2
Regulation: -Meets UNE EN 60730-2-7 regulations- Follow instructions to compliance with the R.D. 842/2002. - Installation, service and maintenance of the
electrical equipment may be carried out by anauthorized person only.-Controls the automatic opening and closing of a circuit according to a time schedule,
stored in memory and established by the user. Work with reserve to avoid deprogramming with power outages.
3
*Characteristics:-DIN RAIL Installation. -Advanced pre-setting one week before -Digital electronics general purpose time switch with daily and weekly programs -Repeat programs
with 16ON/OFF settings, 18 times pulse programs, and setting on/off manually. -Lithium battery power reserve when electric supply cut
time error correction ±30 sec, weekly.
4
Connection & technical data: LOAD
●Voltage rating: AC220V 50/60HZ
●Hysteresis: ≤2 sec/day(25ºC)
●ON/OFF operation: 16 ON & OFF, 18 times pulse
●Power consumption: 7.5VA( max)
●Minimum interval: 1 minute
5
Instructions:
1.First time use this timer switch, please input power and let battery charge. After then press reset Key. 2.At first time, the timer switch is in 24h mode.If you want
change to 12h mode please press on""Key 5 sec, and LCD will display AM If you want recharge to 24h mode ,and press on""key 5 sec to return.
3.Programming: set on&off same time, have 30 seconds to control bell.
Step Key
Programming
1
Setting 1 ON time(display 1 on)
Press
2
Press H+/M+
Set hours and minutes
3
Press D+
Select days of week. Same everyday, MO - FR,MO-SA,SA-SU,MO-WE,TH-
SA,MO WE FR, TU TH SA, different everyday.(If same everyday, not press
this key)
4
Setting 1 off time ,display 1 off
Press
5
Press H+/M+
Set hours and minutes
6
Press D+
If you want same set in every day,you need not press this key
7
Rep eat step 2 -6
Set 2-16 on/off time
8
End
Press
*If need not 16 pulse press""key to the end.
5. Count down:("d" displays at bottom-left corner of LCD)
Step
Key
Programming
1
Press
&
Into count down
2
Press &H+/M+
Setting min/sec
3
Press MANUAL
Start count down
4
Press
Return to start count down
5
Press P&
Exit
7. Auto time error correction, weekly:("7d" displays at
bottom-left corner of LCD)
Step
Key
Programming
1
Press &MANUAL Into count
2
Press D+
Setting 0sec-30sec
3
Press
Confirm
10. Check time: press " " to check whether the time is set correctly or not
Press "MANUAL" and then reset the time and week
Press "" to finish checking and setting, and the time will be display
afterwards
11. Press "MANUAL" to turn on or off at will, except 5
12. Press "D+" and "H+" for 3 seconds to turn off, but the setting will lost.
6
Technical information: -GWT 850ºC.
9
Management of packaging and product waste: PACKAGING WASTE; MATERIAL; PLASTIC; PAPER AND PAPERBOARD; DEPOSIT IN; YELLOW
CONTAINER; BLUE CONTAINER; LOGO IN SPAIN (NOTE); INTERNATIONAL LOGO (NOTE); LOGO IN FRANCE (NOTE); PRODUCT WASTE;
WASTE; WEEE; DEPOSIT IN; SELLING POINT; LOGO (NOTE).
NOTE: The color of the containers may vary depending on the country where it is applied. Check local regulations on this.
Mode d'emploi et de sécurité
1
Présentation:
2
-Conforme à la norme UNE EN 60730-2-7-Suivez ces instructions pour être conforme aux réglementations électrotechniques relatives à le Décret Royal Basse
Tension 842/2002.-Installation, entretien et maintenance des équipements électroniques ne peuvent être effectués que par de personnel autorisée. Contrôle
l'ouverture et la fermeture automatique d'un circuit selon un calendrier, stocké en mémoire et établi par l'utilisateur. Travailler avec réserve pour éviter la
déprogrammation avec des pannes de courant.
●Count down: 1 sec - 99 min 59 sec
●Pulse: 1 sec - 59min 59 sec
●Load capacity: Resistive load: 16A/250V AC
Lagging load: 8A/250V AC
Lamp load: 2000 W
6. Pause
Neither needn't the timer work nor delete the set program. You could just pressand "MANUAL" for 3.
Seconds at the same time to make the timer "AUTO OFF" permanently (only can access when "ON
AUTO"), in that case, the timer can not be changeover, "┌" displays at the bottom-left corner of LCD,
press and "MANUAL" to restore "AUTO OFF", and the timer turn to work normally.
8. Timing
8.1 Press and press D+ repeatedly go to today
8.2 Press and press H+/M+ to change hr/min
9. Having operated items mentioned above, please be sure to reset the ON and OFF according to the current time, press
"MANUAL" in order to display at the bottom line of the LCD
7
Product maintenance:
Halogen Free
-3-
● Power reserve: 3 years (lithium battery)
● Ambient temperature: -10~+40ºC
4. PULSE setting:(" " displays at bottom - left corner of LCD).
Step
Key
1
Press H+ & M+
Into pulse setting
2
Press &H+/M+
Set ting pulse time range 1 sec - 59min 59sec
3
Press &MANUAL
Confirm pulse time range
4
Press
Into setting 1 on time( display 1 on)
5
Press H+/M+
Setting on time
Select days of week. Same everyday, MO-FR,MO-SA,SA-SU,MO -WE,TH-
6
Press D+
SA,MO WE FR, TU -TH-SA, different everyday.(If same everyday, not press
this key)
7
Repeat step 2- 3
Setting 2 - 18 pulse
8
Press
End
9
Press H+&M+
Exit pulse
*If need not 18 pulse press""key to the end.
13. Press "RESET" to reset, but the settings can not be restored
NOTE
●Time setting should according to the time sequence, couldn't be set crossly
●System with quit automatically if there's no operating within 10 seconds, and no
data is saved. It will quit when setting finished.
●Function 3,4,5, can not be used simultaneously
-Clean with a dry cloth.
ENGLISH
off-Present time (ON OFF position). Auto
Programming
8
Safety and usage tips.
FRANÇAIS
Publicidad
