Amazon Alexa - Sulion 101630 Manual

Add device
- Make sure that the terminal is connected to a Wi-Fi network.
-To synchronize the driver it is necessary to connect it to the electri-
cal network and put it in pairing mode
Step 1 Step 2
The luminaire was
ON - OFF - ON -
connected to the conductor
Start blinking (2 times per
OFF - ON
second)
ON OFF
- -In the new screen, different categories of products appear, in this
case "Lighting" is selected and then "Lighting device" is pressed (7).
-Then, press "Confirmed on the flash lamp" (8).
-The new screen will ask to enter the Wi-Fi password and "Confirm"
(9).
- At this moment the application adds the new device to the home
(10) and ends the pairing (11), allowing to change the name and the
allocation of the room. If after making the "Connected" the device
does not synchronize, repeat the steps in the section "Add device
again"
- Once the device is synchronized, it can be accessed (12) from the
control screen to manage the different functions (turn on, turn off,
time delay, etc). (13)
Network conection
1.- Screw type terminal
2.- Class II: 2 Poles (L + N) / Class I: 3 Poles (L + N + TT)
3.- Assigned Voltage 250V and Current 10A.
4.- The terminals must have a minimum capacity of 1.5mm ² for indoor lighting and 2.5mm ² for outdoor lighting.
5.- Verify that the connection block is suitable for the output cable, either a unipolar cable or a bipolar / tripolar
cable.
6.- Check if the connection block to be included must be fixed on the luminaire. It must always be kept away from
heat sources.
7.- IP grade. It must be according to the IP grade marked on the luminaire
8.- In accordance with the EN 60998-2-1 or EN 909998-2-2 standards.
* Respect the color code according to the terminal (L = Brown, black or gray. N = Blue, Ground = Green and yellow)
* Minimum values. In cases of powers higher than 2500W, check the current to know the characteristics of the
connection lock.
* Check if the connection block requires ferrules or special preparation for a correct connection.
- The data shown in this table are merely informative and do not constitute, in any case, unique conditions of
connection to ref by the user or installer. In case of opting for another connection block, the conditions of use that
the EN 60598-1 standard establishes must be respected, highlighting the requirements of creepage distances and
distances in the air for grid connection blocks.
Type A: For making connections inside Class I luminaires. The class II version is similar, but with two poles.
Type B: To make connections to the exterior of Class I luminaires. The Class II version is similar, but with two poles.
Type C: To make connections outside luminaires with class I disconnection. The class II version is similar, but with
two poles. Check that the cable diameter is suitable for the type of connection block.
Type D: To make connections outside luminaires with Grade> IP20. Check that the cable diameter is suitable for the
type of connection block.
www.sulion.es
CIF A28763647 +34 916774540
Step 3
Once the device is flashing, on
the Sùlion IoT app we can add it
6
by pressing the "+" button (6).
ATC: 916749481 - info@sulion.es / SAT : 916749483 - sat@sulion.es
Calle Verano, 51 - 28850 Torrejón de Ardoz - Madrid (España)
Linking devices SÛLION IoT with Google
Assistant
- Download and install Google Home App.
- In the drop-down menu at the top left, select the option "Control of the
house".
- Press "+" button to add devices, select and activate the "SÛLION IoT"
or "TUYA Smart" App.
- Confirm region and enter account and password of SÛLION IoT and
press "Link now" and "Authorize".
- Select devices to assign to different rooms.
- The devices will appear in the "Control of the house" interface.
- Now you can control your devices by voice command in Google As-
sistant.
Linking devices SÛLION IoT with

Amazon Alexa

-Download and install Alexa App.
- In the drop-down menu at the top left, select "Skills and games" and
search / activate the App "SÛLION IoT" or "TUYA Smart".
-Press "Allow use", confirm region and enter account and password of
SÛLION IoT and press "Link now". In the new window press "Authorize".
-Press "Detect devices". The system automatically matches the devices.
Once finalized, the devices are linked with Amazon Alexa.
-Now you can control your devices by voice command in Amazon Alexa.
For more information about the device, you can consult our
complete instructions on our website www.sulion.es/en