Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Free Hand-Head Dual UHF
Functional introduction
Match ( match ID code match+ frequency)
This is new way of operation : Frequency hopping. The mic data is sent by wireless to the receiver
match the frequency. If the matching is successful, the frequency can switched between the 10
frequency. And the handheld can change the frequency at any time, then the receiver will follow the
handheld to adjust the frequency automatically and jump to the corresponding frequency. In this
way, it not only solves the problem of crosstalk, but also provides the flexibility of frequency setting.
The products using frequency hopping have been widely recognized by the market, and meet the
requirement of most products such as KTV room, hand towing box, suitcase, teaching, personal
entertainment, set-top box, wireless speaker, SOUND-BAR wireless bass and so on. Match/change
frequency switching operation ( Touch switch version) : ON/OFF key on / off: boot state, short press the
switch key a boot, long press 2 seconds to enter the shutdown.
Change frequency : Switching frequency of the same situation chain , in the boot time, short press
the battery will hide the switch to switch a frequency point at a time.
Pairing:
a. Handheld Matching: in the state of the round machine, while holding the battery Yang Jian and
the same shutdown button for about 4 seconds to observe the LED digital screen flashes for 1 second
release the hand, hand microphone into the pairing state, LED digital screen- straight flicker.
b, Receiver pairing: when the receiver is switched on, the power switch will automatically enter the
pairing smoke within 2 seconds after dialing the ON file, to see if there is a matching request, there will
be a matching request, will be automatically paired, the matching indicator will flash 3 times to
confirm the success of the pairing, and then the self-excited exit.
Exit pairing : after successful pairing of hand, short press the battery compartment Yang Zang switch a
self-service exit and perform the " switching frequency " operation, the hand flavor is transferred to the
normal launch state, and the RF indicator light of the receiver is lit. The whole process of matching is:
first inlay a cunning shot into the pairing shape (the launch will always send a matching request),
however, when the receiver enters the pairing mode (pairing receive white help exit), L may continue
to match other reception if there is a demand for " a stack of names ", let the launch manually exit the
pairing state and the pairing is completed. For the antenna: the length of the antenna is exposed to 1
/ 4 wavelength, length L (cm) = 7500 / freq (MHz), such as 790MHz frequency, the external demand
length is 47500 / 790-95cm. The receiving module is connected to the system.
USB charging
interface
Antenna
On/Off
3
ON/OFF key
on/off: boot state
UHF Wireless Microphone
Free Hand-Head
Dual UHF
Please read the manual before using the product
USER'S
MANUAL
N EW
S E R IE S

Publicidad

loading

Resumen de contenidos para Audibax UHF676

  • Página 1 USER’S Free Hand-Head Dual UHF MANUAL Functional introduction Match ( match ID code match+ frequency) This is new way of operation : Frequency hopping. The mic data is sent by wireless to the receiver match the frequency. If the matching is successful, the frequency can switched between the 10 N EW frequency.
  • Página 2 Performance Original sound: 1. Using UHF676 to 1697MH band channel A: 677-686MHz: Channel B; 687,696MH2O, strong disturbance The wireless microphone emits the receiving chip, uses 24Bit/ 48KHz ' s high performance audio dedicated O- 2 A / D and D / A processing, uses 1 / 4 π digital modulation and demodulation mode, full digital wireless transmission, which resistance.
  • Página 3 MANUAL Free Hand-Head Dual UHF DE USUARIO Introducción funcional Coincidencia (coincidencia de código de ID de coincidencia + frecuencia) Esta es una nueva forma de operación: salto de frecuencia. Los datos del micrófono se envían de forma inalámbrica al receptor para que coincidan con la frecuencia. Si la coincidencia es exitosa, la frecuencia puede N EW cambiar entre las 10 frecuencias.
  • Página 4 El micrófono inalámbrico emite el chip receptor, utiliza el procesamiento O-2 A/D y D/A dedicado de audio de alto 1. Usando UHF676 a 1697MH canal de banda A: 677-686MHz: Canal B; 687,696MH2O, fuerte resistencia a rendimiento de 24 bits/48 KHz, utiliza el modo de modulación y demodulación digital 1/4 π, transmisión inalámbrica perturbaciones.