Sealife Sea Dragon 5000+ Guía Rápida

Sea Dragon
QUICK Guide
5000+
Sea Dragon 5000+
Pro Photo/ Video Light
(Item SL680)
START
1
1
Charge the battery.
Place battery in charging
tray. The charging status
indicator is located on AC
power adapter and will
turn green when fully
charged. Note: Battery is
pre-installed in the light.
Remove yellow contact
cover, which prevents
accidental power on.
3
3
Insert the battery into the
light [with battery
facing down] and screw
on waterproof battery cap.
5
5
To power ON the light, quickly
push the power button 3 times
within 1 second. To power
OFF, push and hold the button
for 2 seconds.
6
6
Light powers on at 5000 lumens. Push and release the
power button to cycle through 5 brightness modes:
5000 lumens  5000 lumens + Color Boost  3000
lumens  1500 lumens  Red  Repeat cycle.
8
8
IMPORTANT:
1. Avoid using the light above water for more than 30 seconds. The front of the light head quickly gets very hot, which may cause
burning when touched. Water is needed to keep the light cool. A thermal sensor will dim the light if it overheats.
2. After use, soak sealed light in fresh water for 20 minutes to dissolve salt residue. Towel dry. Allow light to fully dry before storage.
3. If water has entered the battery compartment or under the lens port, immediately power off the light. On land, remove the battery.
Allow battery compartment to fully dry. Contact your local SeaLife dealer or SeaLife service center in your country for repair service.
4. Do not use battery that has become wet or if outer casing is cracked or damaged. Dispose of wet or damaged battery in accordance
with your local battery recycling regulations.
5. Remove battery from light before transporting, traveling or long-term storage. Always use the included protective battery cover
when battery is not inside the light or charging tray to prevent accidental short-circuiting the battery contacts.
6. Do not obstruct the safety pressure release valve located under the light head.
7. Observe all SCUBA dive safety rules and always control your buoyancy. Consult your dive instructor for dive safety questions.
8. Visit SeaLife-Cameras.com website for troubleshooting advice, updates to these instructions, spare parts and other helpful information.
label
7
7
To activate emergency signal
mode, push and hold power
button for 4 seconds from power
off state. Push and release power
button to select between 1 sec
blink interval and SOS Morse code.
SEALIFE (C/O PIONEER RESEARCH),
97 FOSTER ROAD, MOORESTOWN, NJ 08057 USA
INFO@SEALIFE-CAMERAS.COM WWW.SEALIFE-CAMERAS.COM
Overview: The Sea Dragon underwater photo-video light delivers 5000 lumens in a smooth 120° beam
without hot spots. A 90 CRI (color rendering index) COB LED array simulates natural sunlight allowing
you to capture vibrant colors and sharp details. The new patent pending Color Boost™ mode combines
specific red and white light that replenishes the lost red for a balanced, warm color effect. The light
has 5 brightness settings in "Easy Mode" and 8 brightness settings in "Advanced Mode", including a 2-
minute 6000 lumen option. Easily mount the light to YS, 1" ball joint or Flex-Connect system of arms,
grips, trays and mounts. The included 50Wh battery delivers 65 minute run time at full power.
What's in the box:
Sea Dragon 5000+ Protective Flex-Connect
Neoprene
light head with YS YS adapter
adapter Cover
2
2
Before each dive, clean and lube
the O-rings, as needed. Only apply a
thin film of lube. O-rings should
appear shiny. Wipe off excess lube.
4
4
Connect light to arm or grip. Use Flex-Connect YS adapter if
connecting light to Flex-Connect system of arms, grips and trays.
Light may also be mounted directly to YS arms and grips. Use
the YS-to-Ball Joint adapter for attaching to 1" ball arms and grips.
Flex-Connect
The battery status indicator, located next to the power button, is
green when battery charge is 100 - 51%, Blue when 50 - 16%, Red
when less than 15%. The LED will blink when using Color Boost.
The light has a 10-minute reserve mode and will dim to 500
lumens for 10 minutes before battery power is completely empty.
9
9
To set light to Advance Mode, push and hold power button for 8 sec from
power off state. Release button when battery status indicator starts blinking.
Push and release power button to select between Easy Mode (1 blink per
sec.) and Advanced Mode (2 blinks per sec.). Push and hold power button for
2 sec to save setting and power off. Advance mode has 8 brightness settings:
5000 lumens > 5000 + Color Boost > 6000 > 6000 + Color Boost > 3000 >
3000 + Color Boost > 1500 > Red > repeat cycle.
Int'l plug adapters
for EU, UK and AU
1" ball joint 50W Li-ion battery with
adapter protective cover, charg-
Spare O-rings, lube,
ing tray and AC power
removal tool and
adapter
1" Ball Joint
GUARANTEE: SeaLife warrants the original
purchaser of this product, for a period of one (1)
year from the date of purchase, that the product is
free from defects in workmanship and materials.
In the event the original purchaser believes there
is a defect in a product, it is recommended that
the purchaser first visit www.sealife-cameras.
com for product updates and information on
how to get warranty repair service. Please contact
your local SeaLife dealer or the importer in the
country where the product was purchased for
return information.
December 2022
cleaning stick
YS