Keter SPRINGFIELD 6X6 Instrucciones De Ensamblado

SPRINGFIELD 6X6
cat : 555519
IMPORTANT:
You must read these instructions carefully before you start to assemble this fence. Please carry out the steps in the order set out in these instructions. Keep these instructions
in a safe place for future reference.
GENERAL INFORMATION:
completion of your fence.
GENERAL ADVICE:
This is a 2 person assembly job. If it is a property line fence, you will want to confirm your property lines
before ordering your fence.The component parts should be checked and laid out in an orderly way, close at hand. Keep all small parts
(screws, etc.) in a bowl so that they do not get lost.
Please keep the tracking number which appears on the box, and refer to this number when calling the service office for questions or complaints.
CARE & MAINTENANCE:
DO NOT use acetone, abrasive cleaners or other special detergents to clean the fence.
For general support and replacement parts, please contact:
US: # 1-888-374-4262
Canada: # 1-800-661-6721
UK: # 0121-5060008
Other European Countries: # 31-1612-28301
String line
Post hole digger / power auger
Mallet
Work shoes
4 timber stakes
2"x 2"x24" (5cm x 5cm x 60cm)
Concrete / dry mix
PARTS & DIMENSIONS
RAIL (x1)
GENERAL ADVICE ON POST HOLES
Use a post hole digger, power auger, or shovel to dig a hole 12" (30 cm) in diameter
and 30" (75 cm) deep. Add 6" (15 cm) of gravel
for post drainage. Insert the post in the center
of the post hole. Level the post and press it
firmly into the hole. Fill the remainder of the hole
with concrete according to the manufacturer's
instructions.
BRACKETS ASSEMBLY
1. Attach three rail brackets (fcb) to one side of the post.
2. Do not assemble brackets on both sides of the post.
3. Place the positioning guide 68"(172 cm) from the top of the post, then place the bracket.
4. Locate all bracket screws (s18b) in the center of the elongated holes on the
bracket for expansion and contraction. The lip of the bracket should be at the bottom.
ASSEMBLY INSTRUCTIONS
The Keter Fence is easy to install. We incorporate methods and procedures used by professional installers to guide you through to the successful
When your fence needs a clean, use a mild detergent solution and rinse with cold clean water.
PANEL KIT POST KIT
MIDDLE
PANEL POST s35 (x12)
(x2) RAILS (x1) 35mm
(x2)
BOTTOM
TOP BRACKET
RAIL (x1) (x6)
Gravel to reduce
frost heave
Hole diameter 12" (30 cm)
TOOLS & MATERIALS
PROJECT PLANNING
1. Stake out fence from beginning to end.
2. Estimate the levelness of the ground.
s18b (x18)
3. Start at the
15mm
4. Dig holes under the post line.
the distance between the hole centers is 6'
(1.82m).
POST
CAP (x1)
For fence sections less than the
standard 6' (1.82m) center-to-center,
simply cut the rails and fence to size
using a power saw with a reinforced
metal blade.
2
POSITIONING GUIDE
A. Fold the positioning guide wings.
B. Positioning guide should be placed 68" (172 cm) from the top of the post.
C. Attach the positioning guide to the post as shown.
D. Place the bracket within the positioning guide hole.
6" (15 cm)
below frost
line
1 2
A
4
FIXING FIRST POST
Place the first post in the hole, checking that it satisfies ALL the following conditions:
HIGHEST GROUND POINT
A
fcb up
Top of
bracket
GROUND
A. Position the first post at the highest ground point of the fence line!
B. Place 2" (5cm) timbers under the bracket to maintain the gap between the fence and the ground.
C. Check the VERTICAL angle in two directions.
D. Use dry or ready-mix concrete and let it dry for 10 minutes.
www.keter.com
highest side of the fence line!
Make sure
B C
B HEIGHT
C
TIMBER
90
2"
(5 cm)
item : EN-V1
1
String/fence line to show
horizontal accuracy.
3
D
5
VERTICAL ADD CONCRETE
D
Builder's
level.
o
o
90