JL Audio XDM700/5 Manual Del Propietário página 3

INSTALLATION CONSIDERATIONS
• Installation requires appropriate tools and
safety equipment. Professional installation
is recommended.
• This product is water-resistant.
Do not submerge or subject to
high-pressure water spray.
• Before installation, turn off the audio
system and disconnect the battery
system from the audio system.
• When possible, install in a dry, well-ventilated
location that does not interfere with factory-
installed systems. If a dry environment
is not available, a location that is not
exposed to heavy splashing may be used.
• Do not install in the engine compartment,
any areas of extreme heat or where it will
be directly exposed to the elements.
• Before cutting or drilling, check for potential
obstacles behind mounting surfaces.
• Carefully route all system wiring away moving
parts and sharp edges; secure with cable ties
or wire clamps and use grommets and loom
where appropriate to protect from sharp edges.
4 | JL Audio® - XDM700/5
SAFETY CONSIDERATIONS
• Only use this product with 12 volt, negative-
ground electrical systems. This product is
not certified or approved for use in aircraft.
• Mount this product securely to prevent
damage or injury in severe conditions.
• An appropriate fuse (or circuit breaker) at
the main power wire is vital for vehicle/vessel
safety and must be installed within 18 inches
(45 cm) of the positive battery connection.
• For ABYC and NMEA applications,
circuit protection is required within 7
inches (18 cm) of the battery, unless the
cable is in an enclosure or conduit.
• Listen to your audio system at
levels appropriate for operating
conditions and hearing safety.
CONNECTIONS
1 2 3
Connection Description
+12 VDC Positive (+12V) Power Connection
1
Ground Negative (GND) Ground Connection
Remote Positive (+12V) Activation Connection
CH. 1 Input Left Input Signal, Black RCA
CH. 2 Input Right Input Signal, Red RCA
CH. 3 Input Left Input Signal, Black RCA
2
CH. 4 Input Right Input Signal, Red RCA
SUB CH. Input Left Subwoofer Input Signal, Black RCA
SUB CH. Input Right Subwoofer Input Signal, Red RCA
Remote Level Remote Level Controller Connection (optional)
3
Control (HD-RLC or MHD-RLC)
(+) Positive Speaker Output
CH. 1 (L)
Speaker
Output
(–) Negative Speaker Output
(+) Positive Speaker Output
CH. 2 (R)
Speaker
Output
(–) Negative Speaker Output
4
(+) Positive Speaker Output
CH. 3 (L)
Speaker
Output
(–) Negative Speaker Output
(+) Positive Speaker Output
CH. 4 (R)
Speaker
Output
(–) Negative Speaker Output
(+) Positive Subwoofer Output
(+) Positive Subwoofer Output
Mono
5
Subwoofer
Output
(–) Negative Subwoofer Output
(–) Negative Subwoofer Output
4 5
Notes
• 4 AWG wire (required)
• Install 60A fuse at (+) battery post
• 4 AWG wire (required)
• 18 – 12 AWG wire capacity
• See Turn On Mode for more info
• Accepts 200mV – 4V input voltage
• See Input Mode for more info
• Operates as an attenuator only:
Fully counter-clockwise = Level Muted
Fully clockwise = Level Unaffected
CH. 1&2 Bridged (+)
• Minimum impedance load:
CH. 1&2 Bridged (–) Stereo mode ≥2 ohms
Bridged mode ≥4 ohms
• 16 – 8 AWG wire capacity
CH. 3&4 Bridged (+)
CH. 3&4 Bridged (–)
• Both positive (+) connections are
connected in parallel internally
• Both negative (–) connections are
connected in parallel internally
• Minimum impedance load: ≥2 ohms
• 16 – 8 AWG wire capacity
5