Publicidad
Idiomas disponibles
Idiomas disponibles
3. Activate the pairing mode in the Mordomus Software by clicking the Start
inclusion button in the device registration menu.
To reach this menu from the main screen click Configurations →
Modules/Addresses → Plus Button [+]
This mode is limited to 5 minutes in software and on the iWL68 device for
safety reasons.
4. After the iWL68 device shows up in the list make sure to click the button
Allow.
The connection status indicator should remain lit in Green color.
From now on the iWL68 device is ready to use.
Method 2 - Manual Setup
1. Activate AP mode and access the configuration page as described in section
5.
2. Enter the (SSID) in the field WiFi Name and password WiFi password. Enter
the Mordomus Home Name in the field Home Name as defined in Mordomus -
> Configurations -> Connectivity: Mordomus Home Name.
By entering the house name, the fields Mordomus local IP and Mordomus
Port should be left blank.
3. Activate the pairing mode in the Mordomus Software by clicking the Start
inclusion button in the device registration menu.
To reach this menu from the main screen click Configurations →
Modules/Addresses → Plus Button [+]
This mode is limited to 5 minutes in software and on the iWL68 device for
safety reasons.
4. After the iWL68 device shows up in the list make sure to click the button
Allow.
The connection status indicator should remain lit in Green color.
From now on the iWL68 device is ready to use.
3. Connection Status indicator codes
WPS discovery mode. Blue.
Connected to Wifi and searching Mordomus. Green.
Access Point mode for manual configuration. Blue.
Connecting to Router. Red.
Connected to Mordomus. Green.
4. Resetting the device to factory defaults
1. Enter AP mode and access the configuration page as described in section 5.
2. Click on the Button Reset all.
iWL68
5. Activating AP Mode (Access Point)
1. Disconnect the iWL68 from the power supply.
2. Set DIP switch
no. 1 to ON. (Switch 1 ON).
3. Connect the iWL68 to the power supply.
The connection status indicator should remain lit in Blue color.
4. Using a wireless device (Laptop, tablet, smartphone) connect to WI-FI
network SSID iWL68_1234 using the password 00000000 (eight zeroes).
5. Ignore message about no internet access and remain connected to this
network.
6. In the address bar of the browser of the device enter the IP 192.168.4.1 in
order to access the configuration page of the iWL68.
7. Enter all the settings on the web page without pressing the Save button yet.
8. Turn off Dip switch
number 1. (Switch 1 OFF).
9. Click on the Save button.
The last four digits of the SSID are the same as the last four digits of the
device's serial number. This mode is limited to 5 minutes on the iWL68
device for safety reasons.
5.1. Configuration page
The configuration page of the iWL68 allows for a manual configuration of:
WiFi Name
WiFi Password
Mordomus Home Name
Mordomus Local IP
Mordomus port
The Reset all button resets all of the above settings and other configurations to
the factory default values.
This product complies with the Electromagnetic
Compatibility Directive 2014/30/EU.
This product conforms with the EU Directive 2011/65,
RoHS
regarding the restriction of use of certain hazardous
substances in electric and electronic devices.
For EU countries only.
All old electrical and electronic devices must be
separated from normal household waste and disposed
of at designated facilities. For further information
contact your local authorities, waste disposal office or
the shop where you bought the device.
PT
iWL68 – 6 entradas, 8 saídas open
collector ON/OFF por Wi-Fi
Características:
•
8 saídas open-collector.
•
6 entradas digitais;
•
leitura de 3 tipos de cliques;
•
leitura de equipamento de segurança (detetores PIR, Gás, Fumo);
•
leitura de interruptores de status (aberto/ fechado);
•
leitura de impulsos de contadores S0 (até 3 entradas);
•
Montagem em calha DIN.
Aplicações:
•
Comutação de relés para iluminação, tomadas, aquecimento,
cilindros elétricos, motores e cargas em geral.
•
Leitura de teclas, interruptores, sensores e contadores com
interface S0.
Especificações Elétricas:
Tensão de alimentação: 15VDC;
Consumo de corrente: 200mA @ 15VDC;
Temperatura Armazenamento: -10ºC a 60ºC;
Temperatura Funcionamento: 10ºC a 50ºC;
Humidade máxima: 80%, sem condensação;
Especificações das Saídas:
v.2310
https://www.mordomus.c
om/mordomus/docs/wifi/i
WL68.pdf
2/7
Publicidad
