Tramontina senseday Manual De Instrucciones

ILLUSTRATED INSTRUCTIONS MANUAL
MANUAL DE INSTRUCCIONES ILUSTRADO
1. Presentation
Tramontina's Senseday Electric Shower
was developed under strict technical regulations for
increased safety, comfort, and ease of use.
Please read all assembly instructions and the
warranty before installing the product.
Keep this manual safe for future reference.
If you have any questions, please contact
sac@tramontina.net.
2. Technical Specifications
MODEL
Voltage Rating
0 Off
Nominal
1 Warm
Wattage [W]
2 Hot
Circuit Breaker or Fuse [A]
Minimum Wiring [mm²]
Maximum Distance [m]*
MODEL
Voltage Rating
0 Off
Nominal
1 Warm
Wattage [W]
2 Hot
Circuit Breaker or Fuse [A]
Minimum Wiring [mm²]
Maximum Distance [m]*
Degree of Protection
Minimum
Operational
Pressure
Maximum
Hydraulic Connection [Input]
THE RESISTIVITY OF WATER SUPPLIED TO THIS PRODUCT MUST NOT BE
LOWER THAN 1,300 OHMS . CM AT 22°C.
* FOR DISTANCES ABOVE THOSE INDICATED IN THIS TABLE USE LARGER
SECTION CONDUCTORS.
THIS PRODUCT IS COMPLIANT WITH THE
ELECTRIC SHOWERS STANDARD NBR 12483.
3. Important for your safety
• This appliance must be installed by qualified persons.
• It is compulsory to turn off the circuit breaker
• Never connect accessories or devices to this
• To avoid hazards, the supply cord of the appliance
• This appliance can heat up water to a temperature
3 TEMPERATURES
4 400 W
110V ˜ 220V ˜
127V ˜ 230V ˜
0 0
2 850 2 850
4 400 4 400 4. Hydraulic Installation
40 25
PREPARING
10 4
• For correct operation of the Senseday Shower, it is
20 40
3 TEMPERATURES
5 500 W
110V ˜ 220V ˜
• When the gap between the installed water tank and
127V ˜ 230V ˜
0 0
3 200 3 200
5 500 5 500
50 32
• Before attaching the Senseday Shower, let water run
10 4
27 32
IP24
• Attach the extension included with the product to the
10 kPa [1 m.c.a.]
400 kPa [40 m.c.a.]
• Apply thread seal tape to the Senseday Shower thread,
Thread - ½ BSP
• The connection thread embedded in the wall, should be
• Attach the appliance manually. Do not use tools in order
• Engage the extension cover in the shower body housing.
senseday
ELECTRIC SHOWER 3 TEMPERATURES
DUCHA ELÉCTRICA 3 TEMPERATURAS
Read before Installing
whenever this appliance is installed, serviced, or
cleaned.
appliance that are not recommended by this manual
or by the manufacturer.
and other electrical components should only be
replaced by the manufacturer or its Authorized
Technical Support. The user is only allowed to
replace the electric coil.
higher than that is adequate safe for use, which can
cause burns. Children, elderly people, sick people,
or people with a physical/mental disability must be
supervised when using the appliance. To do that,
special precautions should be taken to appropriately
regulate water temperature before and during use.
recommended that the installation point be at least 1m
below the water tank and 2.1 meters above the floor
[pic.01].
the Senseday Shower is too large [in tower blocks, for
example], or when the supply comes directly from the
a public drinking water supply, please use the pressure
reducer included with the appliance [pic.02]. For pressure
above 80 kPa [8 m.c.a], please use reducer included with
appliance.
through pipes for a few seconds to remove dirt or any
other residue.
wall-mounted connection. Attach the Senseday Shower
to the end of the extension.
wrapping around the thread 3 to 4 times [pic.03].
diameter of ½". If you have not, use a reduction bush,
by also applying the tape to seal the thread.
to avoid damaging the item.
[pic. 02].