FR-Tec FORMULA Manual De Instrucciones página 5

PROGRAMMING BUTTONS:
PROGRAMMING FEATURES:
a. Programmable buttons: left and right paddle shifters, brake, gas/accelerator, L3, R3
b. Non-configurable (pre-set) buttons: , , , , L1, R1, L2, R2
BUTTON CONFIGURATION PROCEDURE
1. Press the "PROG" button once, and the red LED will flash rapidly.
2. Press the pedal or switch you wish to configure once and the red LED will flash slowly.
3. Press the non-configurable button you wish to assign to it once and the programming light will go out.
4. Configuration is now complete.
RESETTING A BUTTON CONFIGURATION
1. Press the "PROG" button once, and the red LED will flash rapidly
2. Press the pedal or switch you wish to reset and the red LED will flash slowly
3. Press once again the pedal or switch you wish to reset to the factory settings for that pedal or switch and the red LED will
stay lit.
4. The resetting process is now complete
RESTORING FACTORY SETTINGS
1. Press the "PROG" button once, and the red LED will flash rapidly.
2. Press and hold down the "OPTIONS" button for 4 seconds until the red LED goes out.
3. The process is now complete. All buttons, pedals and switches will now be reset and the wheel sensitivity will return to the
default setting of Low.
WHEEL SENSITIVITY CONFIGURATION
The default sensitivity setting is Low.
You can select the sensitivity that best suits your driving style.
The options are Low (default), Medium and High. High= sharp, rapid turning. Low= smooth, gradual turning.
To change the sensitivity mode:
• Low level of sensitivity (default):
1. Press the "PROG" button once, and the red LED will flash rapidly.
2. Press the top button on the D-PAD to set the wheel sensitivity to Low.
3. The sensitivity level has been set when the red LED remains lit.
• Medium level of sensitivity:
1. Press the "PROG" button once, and the red LED will flash rapidly.
2. Press the left or right button on the D-PAD to set the wheel sensitivity to Medium.
3. The sensitivity level has been set when the red LED remains lit.
8
• High level of sensitivity:
1. Press the "PROG" button once, and the red LED will flash rapidly.
2. Press the bottom button on the D-PAD to set the wheel sensitivity to High.
3. The sensitivity level has been set when the red LED remains lit.
PEDAL BOARD FEATURES
The pedal board has 2 pedals:
• Left pedal (Brake)
• Right pedal (Gas/Accelerator)
CONNECTION AND INSTALLATION
CONNECTION AND INSTALLATION WITH PLAYSTATION4™
ATTENTION: Before beginning the installation procedure, make sure that the video console and the PS4™ DualS-
hock4 controller are switched off.
To use the Formula Wheel steering wheel in PS4™ follow the instructions given below in the order shown:
1. Plug the pedal cable into the "Pedals" port on the steering wheel.
2. Use the USB cable provided to connect the original PS4™ DualShock4™ controller (which should be switched off) to the
"Steering Controller" port on the steering wheel.
3. Switch on the console.
4. Plug the steering wheel's USB cable into the USB port on your PS4™ video console.
5. When installation is complete, the red LED on the steering wheel will light up and the PS4™ video console will assign a
connection channel.
6. With the red LED on the steering wheel lit up, press the "HOME" button to access the system menu or play a game.
7. Press the "HOME" button to access the configuration menu or press the "HOME" button for 2 seconds to access the
shutdown menu.
CONNECTION AND INSTALLATION WITH PLAYSTATION3™
To use the Formula Wheel steering wheel in PS3™ follow the instructions given below in the order shown:
1. Plug the pedal cable into the "Pedals" port on the steering wheel
2. Switch on the PS3™ video console
3. Plug the USB cable into the USB port on the video console
4. After booting up, the LED light on the steering wheel will light up and the PS3 video console will assign a connection
channel
5. You can now play a video game or access the PS3™ menu. Press the "HOME" button to access the system menu or press
the "HOME" button for 2 seconds to access the shutdown menu.
9