Publicidad
IMPORTANT
SAFETY
INSTRUCTIONS
READ AND
FOLLOW ALL
INSTRUCTIONS
INSTRUCTIONS FOR INSTALLING THE
ffuuss
one HAND DRYER ON THE WALL
TM
Important safety information. Read before
proceeding.
The installation and electrical wiring work must
be undertaken by a qualified person or persons in
accordance with all applicable codes and standards,
including fire prevention.
The USER MANUAL can be downloaded from our
website.
WARNING:
To ensure the correct functioning of the
ffuuss
one hand dryer:
TM
After installing the unit or each time the unit is
restarted after an electrical disconnection, an
automatic calibration of the capacitive sensors
is performed which lasts for 6 minutes. In order
that this calibration is performed correctly, the unit
should not be handled, activated or any object be
brought close to its near vicinity, during this time.
NOTE: ffuuss
TM
reserves the right to make changes without prior notice.
WARNING:
Before starting any installation work,
you must check the following:
The installation must be designed to be able to
disconnect the device with a disconnection element
separating all the contact points by at least 3mm.
Make
sure the
electricity supply has
disconnected
or
turned
off
before
starting
installation to avoid electrocution or electric shock.
Make sure there are no pipes (gas, water, air) electric
cables, wires or ducts directly behind the drilling
areas.
Before accessing the interior of the device, make
sure you disconnect the power.
WARNING:
Risk of electric shock!
Do not remove the cover or attempt to repair
unless qualified personnel are servicing the unit.
If the cover is removed or handled incorrectly,
the internal elements of the ffuuss
one hand
TM
dryer may cause damage or become permanently
damaged.
WARNING:
In order to avoid the risk of fire or
electric shock, do not expose the
elements and the internal mechanisms
of this unit to rain or humidity.
Check the power supply matches the specifications
on the plate located in the back of the unit.
If this unit is connected to any power supply
different to the one specified on the specifications
plate of the unit, this may result in permanent
damage to or the unsafe and incorrect functioning
of the ffuuss
one hand dryer.
TM
All wiring and electrical work must be performed
by a qualified electrician in accordance with the
rules and applicable federal, state and local laws,
including fire prevention.
According to local wiring regulations, a system for
disconnecting the poles in the fixed wiring of the
device should exist.
been
These instructions must be read carefully before
trying to install the ffuuss
TM
one hand dryer.
Not following the installation instructions exactly
may result in the malfunction of the ffuuss
hand dryer, damage to property or even personal
injury.
ffuuss
shall not be liable for property damage
TM
or personal injury that may result from failure to
comply with these instructions.
Not following these instructions will void this
product's warranty. See the user section for
warranty details.
WARNING
Safety and use:
Children over 8 years can use this hand dryer
ffuuss
, as well as people having reduced
TM
capabilities (physical, sensorial, mental) but only
in the case they had received proper surveillance
and training on the use of the equipment, in order
to make them understand what is the safe use of
the hand dryer ffuuss
and its potential dangers.
TM
Children should always be under the supervision
of an adult to avoid them playing with the device.
An adult must do cleaning and maintenance of the
equipment and it is forbidden to the children.
This equipment has been designed for efficient and
quick hand drying. Do not attempt to dry any other
part of the body.
WARNING:
To reduce the risk of fire, electric shock
or personal injury, follow the steps
detailed below:
1- Use this unit only as instructed by the
manufacturer. If in doubt, contact the manufacturer.
2- Before cleaning or servicing the unit, make sure
the power supply is cut by disconnecting the fixed
wiring to the ffuuss
TM
one hand dryer to ensure
the machine is not switched on accidentally or to
avoid an electric shock that may occur during its
one
TM
repair or maintenance.
3- Any installation or wiring work must be
undertaken by qualified personnel in accordance
with the codes and standards in force.
4- When cutting or drilling into the wall, do not
damage the electrical wiring or other hidden
services.
WARNING:
CLASS 1 LASER PRODUCT
IEC 60825-1 Ed.3 (2014)
SAVE THESE
INSTRUCTIONS
Publicidad
