Publicidad
Idiomas disponibles
Idiomas disponibles
English
5. Slowly lift the handle to lower the blade, finding the edge
of the paved surface and start edging. Then move tool
forward slowly along edge of paved surface, keeping the
edge guide pressed lightly against the pavement edge.
‑
For the first edging each season, it is best to move
forward slowly because grass is thickest then.
Subsequent edging will be completed more rapidly.
If the tool slows down, back it up an inch or two
until the blade comes up to normal speed. During
edging some sparks may be generated from hitting
stones. This is normal. Do not attempt to edge when
the grass or soil is wet or moist—for electrical safety
and to prevent clogging of the blade chamber. If you
must edge under conditions that cause the blade
chamber to become clogged, release trigger, wait
for blade to come to complete stop. Remove battery
pack and remove clogged material with a stick. To
continue to operate the tool in a clogged condition
will seriously overload the motor.
CAUTION:
blade chamber by dropping or tapping the tool on the
ground. This can damage the unit. Keep hands clear of
edge guide and blade when cleaning as these wear to
a very sharp point during edging.
Landscaping/Trenching
WARNING:
Trenching, inspect and ensure there are no exposed or
buried cables, pipes or other objects that may create a
hazard or interfere with operating the edger. Set depth
to only that required for the job. Do not overload. If tool
slows, pull back slightly and wait until blade comes up
to normal speed.
Storage
DANGER:
blade to come to complete stop.
Remove and clean any debris from the outside of the edger
and inside of guard before storage. Refer to MAINTENANCE
section. If necessary, the edger may be stored by hanging on
a hook by its handle.
CAUTION:
switch trigger.
NOTICE:
to fertilizers or chemicals. Such storage can cause
rapid corrosion.
12
Do not attempt to unclog the
Before Landscaping or
Remove the battery. Wait for
Do not hang edger on the
Do not store the tool on or adjacent
Preventing Corrosion
Fertilizers and other garden chemicals contain agents that
greatly accelerate the corrosion of metals. If you use the
tool in areas where fertilizers or chemicals have been used,
the tool should be cleaned immediately afterwards. Wipe
all exposed parts with a damp cloth. You may lubricate only
metal parts with a light petroleum based oil.
When cleaning, DO NOT immerse tool in water or squirt it
with a hose.
MAINTENANCE
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
E
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING:
all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI
Z87.1 approved eye protection when performing
this procedure.
WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
a liquid.
Accessories
WARNING:
those offered by D
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
WALT recommended accessories should be used with
D
E
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
To reduce the risk of serious
Blow dirt and dust out of
Never use solvents or other
Since accessories, other than
WALT, have not been tested with
E
WALT call 1‑800‑4‑D
WALT
E
E
Publicidad
