Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
SPECIAL
NOTICE:
Exposure
to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve
damage
in the fingers,
hands,
and
joints of people prone to circulation disorders
or abnormal swellings.
Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur
such
as numbness,
pain,
loss
of
strength,
change in skin color or texture,
or
loss of feeling in the fingers, hands, or joints,
discontinue
the use of this tool and seek med-
ical attention.
An anti-vibration
system does
not guarantee
the avoidance
of these prob-
lems. Users who operate power tools on a
continual
and regular
basis
must monitor
closely their physical condition and the condi-
tion of this unit.
SPECIAL
NOTICE:
This unit is equipped
with a temperature
limiting muffler and spark
arresting
screen which
meets the require-
ments of California
Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota,
New Jersey, Ore-
gon,
and Washington
require
by law that
many
internal
combustion
engines
be
equipped with asparkarresting
screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation
of the law. For normal
homeowner
use, the muffler and spark arrest-
ing screen will not require any service.
After
50 hours of use, we recommend
that your
muffler be serviced or replaced by your Au-
thorized Service Dealer.
• Locate the decal on the handlebar. This de-
caI includes two arrows. Position the han-
dlebar on the mounting
bracket
between
these arrows.
• Position the bracket cover over the handle-
bar. Again make sure the handlebar is be-
tween the arrows.
• Insert screws and hand tighten
only. Be
sure the handlebar
is installed
correctly;
then, tighten each screw securely with the
large hex wrench.
Bracket Cover
_
Screw
Handlebar
Mountinc
Bracket
d_kWARNING:
Remove fuel cap slowly
when refueling.
This engine is certified to operate on unleaded
gasoline. Gasoline must be mixed with a good
quality 2-cycle air-cooled engine oil designed to
be mixed at a ratio of 40:1. Poulan/Weed Eater
brand oiI is recommended.
(A 40:1 ratio is ob-
tained by mixing 3.2 ounces of oil with I gallon of
unleaded gasoline). When mixing fuel follow the
instructions printed on the oil container: Always
read and follow the safety rules under FUEL
SAFETY.
It is normal for the fuel filter to rattle in the
empty fuel tank. Finding fuel or oil residue on
muffler
is normal due to carburetor
adjust-
ments and testing done by the manufacturer.
ASSEMBLY
dCiWAI_NINI3:
If received assembled,
repeat all steps to ensure your unit is properly
assembled
and all fasteners are secure.
TOOLS
REQUIRED:
• 2 hex key wrenches
(provided)
• Adjustable
wrench or large pliers
• Phillips screwdriver
ATTACH
THE TUBE
TO THE EN-
GINE
• Slip the tube with drive shaft into the engine.
• Insert and tighten
two screws, washers,
and nuts into clamp holes in engine.
ATTACHING
THE HANDLEBAR
A
_IL DANGER:
RISK OF CUT. To avoid
serious injury, the barrier portion of the han-
dlebar must be installed as shown to provide
a barrier between
operator and the spinning
blade.
HOW TO STOP YOUR
UNIT
• Move the ON/OFF switch to the OFF posi-
tion.
• if engine does not stop, move choke to the
FULL CHOKE position.
HOW TO START
YOUR
UNIT
DANGER:
The cutting bladewill
turn while starting the engine.
oWARNING:
Avoid any contact with
the muffler. A hot muffler can cause serious
burns.
• Rest engine and shield on ground, support-
ing unit, so the blade is not touching
the
ground.
STARTING
A COLD
ENGINE
(or a
warm
engine
after
running
out of
fuel)
• Move the ON/OFF switch to the ON posi-
tion.
• Slowly press the primer bulb 6 times.
• Move choke lever to the FULL CHOKE
position.
Publicidad
Tabla de contenido
