Descargar Imprimir esta página

Makita UX01G Manual De Instrucciones página 16

Ocultar thumbs Ver también para UX01G:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 75
Reverse button for debris removal
WARNING:
Switch off the tool and remove
the battery cartridge before you remove entan-
gled weeds or debris which the reverse rotation
function can not remove. Failure to switch off and
remove the battery cartridge may result in serious
personal injury from accidental start-up.
This tool has a reverse button to change the direction of
rotation. It is only for removing weeds and debris entan-
gled in the tool.
To reverse the rotation, tap the reverse button and pull
the switch trigger while depressing the lock-off lever
when the cutting tool is stopped. The speed indicators
start blinking, and the cutting tool rotates in reverse
direction when you pull the switch trigger.
To return to regular rotation, release the trigger and wait
until the cutting tool stops.
► Fig.11: 1. Speed indicator 2. Reverse button
NOTE: During the reverse rotation, the tool operates
only for a short period of time and then automatically
stops.
NOTE: Once the tool is stopped, the rotation returns
to regular direction when you start the tool again.
NOTE: If you tap the reverse button while the cutting
tool is still rotating, the tool comes to stop and to be
ready for reverse rotation.
Electronic torque control function
The tool electronically detects a sudden drop in the
rotation speed which may cause a kickback. In this
situation, the tool automatically stops to prevent further
rotation of cutting tool. To restart the tool, release the
switch trigger. Clear the cause of sudden drop in the
rotation speed and then turn the tool on.
NOTE: This function is not a preventive measure for
kickbacks.
ASSEMBLY
WARNING:
Always be sure that the tool is
switched off and battery cartridge is removed
before carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may result
in serious personal injury from accidental start-up.
WARNING:
Never start the tool unless it is
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Mounting the handle
Attach the handle with supplied clamps and bolts. Make
sure that the handle is located between the spacer and
the arrow mark. Do not remove or shrink the spacer.
► Fig.12: 1. Clamp 2. Hex socket bolt 3. Handle
4. Arrow mark 5. Spacer
When using the following attachments, be sure to attach
the barrier to the handle using the screw on the barrier.
Brushcutter attachment *
Rotary scissors attachment
Grass trimmer attachment *
Edger attachment
*. Only when metal blade is attached.
► Fig.13: 1. Barrier 2. Screw
Mounting the attachment pipe
CAUTION:
Always check that the attachment
pipe is secured after installation. Improper instal-
lation may cause the attachment falling off from the
power unit and cause personal injury.
Mount the attachment pipe to the power unit.
1.
Turn the lever of the power unit toward the attach-
ment side.
► Fig.14: 1. Lever
2.
Remove the cap of the attachment. Align the pin
with the arrow mark and insert the attachment pipe until
the release button pops up.
► Fig.15: 1. Release button 2. Arrow mark 3. Pin
3.
Turn the lever toward the power unit side.
► Fig.16: 1. Lever
Make sure that the surface of the lever is parallel to the
pipe.
To remove the pipe, turn the lever toward the attach-
ment side and pull the pipe out while pressing down the
release button.
► Fig.17: 1. Release button 2. Lever 3. Pipe
Adjusting the handle position
Adjust the handle position to obtain comfortable han-
dling of the tool.
Loosen the hex socket head bolt on the handle. Move
the handle to a comfortable working position and then
tighten the bolt.
► Fig.18: 1. Handle 2. Hex socket head bolt
16 ENGLISH

Publicidad

loading