Publicidad
Idiomas disponibles
Idiomas disponibles
Operating Instructions and Parts Manual
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your product. Read this manual carefully. Learn the product's
applications and limitations, as well as potential hazards specific to
it. The use of this product is simple and straightforward if you follow
the instructions. When operating this product, use common sense
and only use this product for its intended purpose.
2. Maintain labels and nameplates on this product. These carry
important information. If unreadable or missing, contact OEMTOOLS
for a replacement.
3. Maintain this product with care. Keep it dry and clean – and free
from brake fluid, oil, and grease (if applicable).
4. Check for damage. Check your product regularly. If part of the
product is damaged, it should be carefully inspected to make sure
that it can perform its intended function correctly. If in doubt, the
part should be repaired. Refer all servicing to a qualified technician.
Consult your dealer for advice.
5. Check for misalignment or binding of moving parts, breakage
of parts, and any other condition that may affect the product's
operation.
6. DO NOT use a damaged product. Tag damaged products "DO NOT
USE" until repaired. If damaged, have the product serviced before
using. Many accidents are caused by poorly maintained products.
7. Service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could
create a risk of injury.
8. When servicing a product, use only identical replacement parts. Use
of unauthorized parts or failure to follow maintenance instructions
could create a risk of injury.
9. Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one product may
become hazardous when used on another product.
10. Keep work area clean and well lit. Cluttered or dark work areas invite
accidents.
11. Maintain a safe working environment. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Keep the work
area free of obstructions, grease, oil, trash, and other debris. DO NOT
use this product in a damp or wet location.
12. Keep children away from the work area. Never let a child handle this
product without strict adult supervision.
13. Store this product out of the reach of children and untrained persons.
This product may be dangerous in the hands of untrained users.
14. DO NOT operate this product if under the influence of alcohol or
drugs. Read warning labels on prescriptions to determine if your
judgment or reflexes are impaired while taking drugs. If there is any
doubt, DO NOT attempt to operate.
15. Use safety equipment. Eye protection should be worn at all times
when operating this product. Use ANSI approved safety glasses.
Everyday eyeglasses are NOT safety glasses. Dust mask, non-skid
safety shoes, hard hat or hearing protection should be used in
appropriate conditions.
16. Wear proper apparel. Loose clothing, gloves, neck-ties, rings,
bracelets or other jewelry may present a potential hazard when
operating this product. Keep all apparel clear of the product.
17. DO NOT overreach. Keep proper footing and balance at all times
when operating this product.
18. Keep away from flammables. DO NOT attempt to operate this
product near flammable materials or combustibles. Failure to comply
may cause serious injury or death.
19. Avoid accidental fire and/or explosion. DO NOT smoke near engine
fuel and battery components.
8/20
2020 OEMTOOLS
®
HEAVY DUTY HUB, ROTOR
AND DRUM PULLER
20. We believe the information contained herein to be reliable. However,
general technical information is given by us without charge and
the user shall employ such information at their own discretion and
risk. We assume no responsibility for results or damages incurred
from the use of such information in whole or in part. Always refer to
specific instructions and technical information supplied by vehicle
manufacturer.
21. The manufacturer declines any and all responsibility for property
damage or injury if said damage is the result of unskillful handling
®
by the operator or of failure to observe the basic safety rules set
forth in the instruction manual.
22. The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur.
The operator must understand that common sense and caution are
factors which cannot be built into this product, but must be supplied
by the operator.
PRODUCT DESCRIPTION
Designed for the removal of the of brake drums and rotors on most
FWD and AWD (some RWD) vehicles. This tool can also be used to
pull some larger parts, such as: wheels, gears, pulleys, hubs and
flywheels.
PRODUCT SPECIFICATIONS
Load Rating
Max Spread
Max Reach Drum/Rotor
Max Reach Hub
Pressure Screw Hex
Pressure Screw Length
Pressure Screw Thread Length 6.25" (158 mm)
Forcing Nut Hex
Hub Adapters Included
Impact Rated
CONTENTS
(1) T-bar Frame, (2) Drum/Rotor Puller Jaws, (2) Hub Puller Jaws, (2)
Set Knobs, (3) Hub Adapters, (2) Hardened Washers, (1) Forcing Nut,
(1) Extended Forcing Nut (G), (1) Pressure Screw
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
WARNING: ALWAYS reference the vehicle maintenance manual
prior to use.
WARNING: PRIOR to applying load, ensure that the puller jaws
are straight and making secure contact with the part being pulled. An
insecure load may cause the tool or part to dislodge unexpectedly,
causing injury or damage to personal property.
WARNING: Ensure all clothing, fingers and any appendages
are not placed between the puller jaws and the part being pulled, or
between the part being pulled and the T-bar.
WARNING: ALWAYS ensure that the load is being placed in the
correct direction prior to pulling. Failure to do so may cause damage
to the part or tool.
WARNING: If a ratchet strap is to be used, ensure the strap is
not damaged and is not placed between the puller jaws and the part
being pulled, this may cause the pulling system to fail and result in
injury or property damage.
2
25106
7 Tons
14" (355 mm)
5.1" (130 mm)
4.1" (105 mm)
1-1/4" (32 mm)
10.5" (266 mm)
1-1/4" (32 mm)
Small (32.8 mm),
Medium (36.9 mm),
Large (45 mm)
Yes
Publicidad
