Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATING
INSTRUCTIONS
NOTE: Before using the tool, read the instruction book
carefully.
INTENDED USE
The machine is intended for driving in and loosening screws as well
as for drilling in wood, metal, plastic, masonry and concrete.
BEFORE OPERATION
1. CHARGING THE BATTERY PACK
a) Do not use any charger other than that specifically provided for
use with the equipment.
b) If the battery pack is very hot you must remove your battery pack
from the charger and allow time for the battery to cool down
before recharging.
c) The battery in your new tool is not charged when it leaves the
plant. Therefore it must be full charged before using the first
time.
d) Please charge the battery to reach full or no less than half charge
before storage. If the tool will not be used for long periods of
time, charge the battery every 3-6 months.
CHARGING PROCEDURE (SEE FIG. A)
1) Plug the charger into an appropriate outlet. The light will be
green.
2) Slide the battery pack into the charger, the light will turn to red to
indicate the charging process has started.
3) When charging is completed, the light will turn to green. The
pack is now fully charged, unplug the charger and remove the
battery pack.
CHARGING INDICATOR
This charger is designed to detect some problems that can arise
with battery packs. Indicator lights indicate problems (see table
below). If this occurs, insert a new battery pack to determine if the
charger is OK. If the new battery charges correctly, then the original
pack is defective and should be returned to a service center or
recycling service center. If the new battery pack displays the same
problem as the original Battery Pack, have the charger tested at an
authorized service center.
Light
Red on
Green on
WARNING: When battery charge runs out
after continuously use or exposure to direct
sunlight or heat, allow time for the tool to cool
down before re-charging to achieve the full charge.
2. REMOVE OR INSERT BATTERY PACK (SEE FIG.
B,C)
Press the battery pack release button and remove the battery
pack from the tool. After recharge slide the battery pack into tool's
battery port. A simple push and slight pressure will be sufficient.
16
Status
Charging
Fully Charged
OPERATION
1. ON / OFF SWITCH (SEE FIG. D)
Depress the On/Off switch to start and release it to stop your drill.
The on/off switch is fitted with a brake function which stops your
chuck immediately when you quickly release the switch.
It is also a variable speed switch that delivers higher speed and
torque with increased trigger pressure. Speed is controlled by the
amount of switch trigger depression.
WARNING: Do not operate for long periods at
low speed because excess heat will be
produced internally.
WARNING: When overload occurs, release
the On/Off switch immediately to avoid the
motor overheating.
2. SWITCH LOCK (SEE FIG. E)
The switch trigger can be locked in the OFF position. This helps to
reduce the possibility of accidental starting when not in use. To lock
the switch trigger, push the rotation control in the center position.
3. FORWARD AND REVERSE ROTATION CONTROL
(SEE FIG. F1, F2)
Forward rotating: push the forward/reverse rotation control to the
left (the drill points away from you). It is used for drilling and screw
driving.
Reverse rotation: push the forward/reverse rotation control to the
right (the drill points away from you). It is used for remove screws or
release a jammed drill bit.
WARNING: Never change the direction of
rotation when the chuck is rotating, wait until
it has stopped!
4. TWO-SPEED GEAR CONTROL (SEE FIG. G)
The drill has a two-speed gear control designed for drilling or driving
at LO (mark is 1) or HI (mark is 2) speeds. A slide switch is located
on top of the drill to select either LO or HI speed. When using the
drill in the LO speed range, the speed will decrease and the drill will
have greater power and torque. When using the drill in the HI speed
range, the speed will increase and the drill will have less power and
torque.
GEAR I
Low speed range: for screwdriving or working with large drilling
diameter.
GEAR II
High speed range: for working with small drilling diameter.
WARNING: To prevent gear damage, always
allow the chuck to come to a complete stop
before changing the direction of rotation or
the two-speed gear control.
WARNING: When overload occurs frequently
on the high speed gear, switch to the low
speed gear to avoid the motor overheating.
5. CHUCK ADJUSTMENT (SEE FIG. H)
To open the chuck jaws rotate the front section of the chuck. Insert
the drill bit between the chuck jaws and rotate the front section
in the opposite direction. Ensure the drill bit is in the center of the
chuck jaws. Finally, firmly rotate the front chuck section in the
opposite directions. Your drill bit is now clamped in the chuck.
6. TORQUE ADJUSTMENT (SEE FIG. I)
The torque is adjusted by rotating the torque adjustment ring. The
EN
Publicidad
