Chicco OASYS 2/3 FIXPLUS Instrucciones De Uso página 21

sponding ISOFIX anchorage points on the car
seat, located between the backrest and the seat
(diag. 15).
WARNING! Check that the two indicators (Q) are
green which means the system has been installed
correctly (diag.16).
5. Push the child car seat fi rmly against the back-
rest of the car seat (Diag. 17), pushing the lever
(O) to ensure maximum adherence of the child
car seat backrest against the car seat.
6. Sit the child inside with his back against the
child car seat backrest and follow the instruc-
tions 3-4-5-6-7 provided in the previous chap-
ter to install the car safety belts, (Fitting the
child car seat inside the vehicle using safety
belts and rigid FixPlus clasps and placing the
child inside) paying attention to every single
detail.
The rigid FixPlus clasps are designed to improve
the levels of comfort and stability of the child car
seat. It is possible to use the Oasys FixPlus child
car seat without these optionals, if you encounter
problems installing them in your car.
Installing the child seat inside the vehicle
without the child inside
When the child is not travelling in the car, the
child car seat should be left secured by the vehicle
three-point safety belt, or stowed away in the car
boot. An unsecured child car seat may be a source
of danger for the other passengers in the event of
an accident or sudden braking.
How to remove the child from the child car
seat
Release the car belt buckle, accompanying the
belt as it retracts.
Removal of the child car seat
WARNING! Remove the child from the child car
seat before removing it.
1. Release the car safety belt.
2. Unthread the diagonal strap through the guide,
accompanying it as it retracts.
If the rigid clasps have been used to fasten the car
seat in place, they must now be released from the
anchor points:
1. Pull the two red buttons on the rigid clasp re-
lease system ® towards you, release the clasps
from the corresponding Isofi x anchor points on
the car seat (Diag. 18) so that the indicator is
completely red.
2. Hold the lever up (O) as you push the rigid
clasps all the way into the base of the child car
seat, (Diag. 19).
Installing and removing the cup holder
The child car seat has 2 inserts, one on the right
and one on the left of the side of the seat where
you can fi t the cup holder whenever you like.
To install the cup holder:
1. Insert the cup holder into the relative guide
(Diag. 20)
2. Press the cup holder downwards until it clicks
into place (Diag. 21).
WARNING! Do not place glass containers or hot
liquids on the cup holder as they could harm the
child.
To remove it:
1. Press the lever on the back of the cup holder and
lift it upwards, out of the guide (Diag. 22)
The cup holder guides are fi tted with a special
device that makes sure it always remains in a hori-
zontal position.
To rotate and position the cup holder:
1. Press the lever on the back and rotate it to the
desired position
Adjusting the height of the back rest
The height of the headrest can be adjusted to 10
different positions to adapt the child car seat to
the height of the child.
Make sure the child's head is always well protect-
ed and the car diagonal safety belt is positioned
properly on his shoulder.
When adjusting the height of the backrest, check
that the diagonal belt loop (B) is positioned at
a maximum of 2 cm above the child's shoulder
(Diag. 23)
To make the adjustment:
1. Use one hand to press the child car seat back-
rest height adjuster lever (L) located on the back
of the headrest (Diag. 24)
2. Raise/lower the backrest to adapt it to the
height of the child's shoulders (Diag. 25)
3. Release the lever checking that it has clicked
into the desired position.
Adjusting the width of the back rest
The width of the backrest can be adjusted to
adapt the child car seat to suit the physique of
the child.
Use the backrest width regulator wheel (K) locat-
ed above the headrest, to adjust the width:
1. Rotating it counter clockwise will increase the
width of the backrest (Diag. 26) while rotating
it clockwise will decrease the width (Diag. 27).
21