PPA Citrox Serie Manual De Instrucciones

ATTENTION:
Do not use the equipment
without first reading the
instruction manual.
USER'S MANUAL
SMART SLIM
MAGNETIC SENSOR
P31564 - 09/2022
Rev. 0
TECHNICAL FEATURES
- Long-lasting Lithium battery.
- Easy installation.
- Installation in indoor environments.
- Transmission time on detection of 2 seconds with signaling LED.
- Transmission frequency at 433.92Mhz.
- Supply voltage: 3V lithium battery.
- Stand-by consumption: 0.4 uA @ 3Vdc.
- Transmission consumption: 12mA @ 3Vdc.
- CR2032 battery.
- 100-meter Range without barrier.
- Max. gap between sensor and magnet:1 cm.
SENSOR DIMENSIONS
Note: All dimensions are in millimeters.
LINE
MAIN COMPONENTS OF THE BOARD
The figure below shows the sensor board with its components:
CR2031 Battery
RECORDING THE SENSOR IN THE ALARM PANEL
- Enter in wireless sensor recording mode on the alarm panel.
- Activate the sensor for signal transmission, and check if the LED stays on for 2 seconds.
- Wait for confirmation from the alarm panel. If necessary, repeat the procedure to trans-
mit again.
- Below is an illustration of this procedure:
PRESS AND RELEASE
ACTIVATE THE SENSOR
THE LEARNING BUTTON
GENERAL TERMS AND CONDITIONS OF WARRANTY
MOTOPPAR, Industry and Commerce of Automatic Gate Operators Ltd., registered with the CNPJ (National
Registry of Legal Entities) under Number 52.605.821/0001-55, located at 3526 Dr. Labieno da Costa Machado
Avenue, Industrial District, Garça – SP – Brazil, Zip Code 17400-000, manufacturer of PPA Products, hereby
guarantees this product against design, manufacturing or assembly defects and/or supportively as a result
of material quality flaws that could make its intended use improper or inadequate, within a legal period of
ninety days from time of acquisition, provided that the installation instructions described in the instruction
manual are observed.
Due to the credibility and trust placed on PPA products, we will add 275 more days to the period mentioned
above, reaching a warranty period of one year, likewise counted from the time of acquisition proven by
consumer through proof of purchase (Customer Receipt).
In case of defect, within the warranty period, PPA responsibilities are restricted to the repair or substitution of
the product manufactured by the company, under the following conditions:
1. Repair and readjustment of equipment may only be carried out by PPA Technical Assistance, which is
qualified to open, remove, and substitute parts or components, as well as repair defects covered by this
warranty; thus, failure on observing this guideline and the verified use of any non-original parts will cause
the resignation of this warranty on the part of the user;
2. The warranty will not extend to accessories such as cables, screw kit, fixing brackets, power supplies etc.;
3. Expenses for packaging, transportation and product reinstallation will be sole responsibility of the
consumer;
4. The equipment must be sent directly to the Company responsible for the sale (manufacturer's
representative), through the address contained in the purchase invoice, properly packed, thus avoiding
loss of the warranty;
5. Within the additional period of 275 days, visits and transportation in places where authorized technical
assistance is not available will be charged. The cost of transportation of the product and/or technician will
be sole responsibility of the consumer and
6. The substitution or repair of the product does not prolong the warranty time.
This warranty will be terminated if the product:
1. Is damaged by natural agents, such as atmospheric discharges, floods, wildfires, landslides etc.;
2. Is installed in an improper electric power supply or if it is not according to any of the installation instructions
displayed on the manual;
3. Shows defects caused by droppings, collisions or any other physical accident;
4. Shows signs of product violation or attempted repair by unauthorized personnel;
5. Is not used for its intended purpose;
6. Is not used under normal conditions;
7. Is damaged by accessories or equipment connected to it.
Recommendation:
We recommend that both the installation and the maintenance of the operator to be performed by an
authorized PPA technical service. If the product fails or has an improper operation, seek an Authorized
Technical Service to fix it.
Manufactured by: Motoppar da Amazônia Indústria e Comercio de Eletrônicos LTDA
Praça Linear, 100, Bloco 2 - Centro - Santa Rita do Sapucaí - MG - CEP 37540-000 - Brasil
CNPJ: 09.084.119/0002-45
www.ppa.com.br | +55 14 3407 1000
MICROCONTROLLER MAGNETIC SENSOR
SIGNALING LED
'STATUS PROG' BLINKS
QUICKLY.
ACTIVATE THE WIRELESS
SENSOR
LINE