Publicidad
Idiomas disponibles
Idiomas disponibles
WIRING DIAGRAM
IPS12 - 60 W- 96 W - 216 W
+ -
-
+
+
12 VDC / 5 A
12 VDC / 8 A
60W
96W
DC OK
DC OK
12
14
28
P O W E R
P O W E R
V. ADJ
V. ADJ
S U P P LY
S U P P LY
I P S 1 2 - 6 0 W
I P S 1 2 - 1 2 0 W
100 - 240 VAC
100 - 240 VAC
L
N
N
L
+
Output terminal
-
Output terminal
DC OK
Green LED lights when Output Voltage on
L
AC Input terminal Live line (fuse in line)
N
AC Input terminal Neutral line
V. ADJ
Output voltage adjust trimmer.
The output voltage rises when a trimmer is turned clockwise.
PE (Protective Earth ) Input
INSTALLING / STORAGE ENVIRONMENT
1.
Store the product with ambient temperature -40 to + 85 °C, and relative humidity
5 to 95 % (No Dewdrop).
2.
Avoid operating the unit in over current, short circuit conditions or outside the
specified input voltage range as damage may occur.
3.
Confirm connections to input/output terminals are correct as indicated in the
instruction manual.
4.
Use the product where the relative humidity is 5 to 95 % (No Dewdrop).
5.
Avoid places where the product is subjected to direct sun light.
6.
Avoid places where the product is subjected to penetration of liquid, foreign
substance or corrosive gas.
7.
A device such as a contact breaker may be a vibration source. Set the Power
Supply as far as possible from possible sources of shock or vibration.
8.
If the Power Supply is used in an area with excessive electronic noise, be sure to
separate the Power Supply as far as possible from the noise sources.
9.
Don't use the product in the environment with strong electromagnetic field,
corrosive gas and conductive substance.
SAFETY INSTRUCTIONS
•
This manual is meant for personnel involved in wiring installation operation &
routine maintenance of the equipment.
•
Disconnect power supply of your system before starting any installation
operation or wiring.
•
Improper installation operation or wiring may impair safety & failure of the unit
or electrical shock or damage.
•
Connect the ground completely. A protective earthing terminal stipulated in
safety standards is used. Electric shock or malfunction may occur if ground is
not connected property.
CERTIFICATIONS
CE Marking, when applied to a product covered by this handbook indicates
compliance with :
•
Restriction Of the use of certain Hazardous Substances Directive 2011/65/EU
(RoHS)
•
LVD Directive 2014/35/EU
•
EMC Directive 2014/30/EU
•
UL-508 approved
•
UKCA
For more information please go to www.crouzet.com
Industrial Power Supply
+ -
-
+
-
12 VDC / 18 A
DC ON
216W
DC OK
DC OK
DC OK
P O W E R
12
28
14
S U P P LY
12
14
V. ADJ
V. ADJ
V. ADJ
I P S 1 2 - 2 4 0 W
100 - 240 VAC
L
N
IPS12 & IPS24
IPS24 - 60 W- 120 W - 240 W - 480 W
+ -
-
-
+
+
24 VDC / 2.5 A
24 VDC / 5 A
60W
120W
DC OK
DC OK
DC OK
24
28
28
24
P O W E R
P O W E R
V. ADJ
V. ADJ
V. ADJ
S U P P LY
S U P P LY
I P S 2 4 - 6 0 W
I P S 2 4 - 1 2 0 W
100 - 240 VAC
100 - 240 VAC
L
N
L
N
WIRING INSTRUCTIONS
1.
To prevent risk of electric shock, power supply equipment must be
kept OFF while wiring.
2.
Terminals and electrically charged parts must not be touched when the
power is ON.
3.
Wiring shall be done strictly according to terminal layout provided in the
operating manual.
TERMINAL CONNECTING METHOD
WARNING
•
Pay attention to the input wiring. If it is connected to wrong terminal, the power
supply will be damaged.
•
Input must be off when making connections.
•
The output load line and input line shall be separated and twisted to improve
noise sensitivity.
•
When connecting or removing input and output wire, do not apply stress to
PCB.
LOAD
+ -
WARNING
WARNING
BEFORE USING THE POWER SUPPLY UNIT
Pay attention to all warnings and cautions before using the unit. Incorrect usage
could lead to an electrical shock, damage to the unit or a fire hazard.
•
Do not modify, disassemble the power supply.
•
Read instruction manual before connecting to mains.
•
Do not use the power supply without proper grounding (Protective Earth).
•
Minor electric shock, fire or product failure may occasionally occur. do not
allow any pieces of metal or conductors or any clippings or cuttings resulting
from installation work to enter the product.
•
Electric shock hazardous on the connector section.
•
WEEE symbol for electrical and electronic equipment waste management.
!
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
INSTALLATION SHEET
Ref.: C.MC.SAV.00028_EN
28
I P S 2 4 - 2 4 0 W
N
L
a
WARNING
I P S 2 4 - 4 8 0 W
Publicidad
