Resumen de contenidos para Truper Expert COPLA-60X
- Página 1 Manual 60 A Plasma Cutter COPLA-60X Applies for: Code Model 17332 COPLA-60X Read the user’s manual thoroughly CAUTION before operating this tool.
- Página 2 Contents CAUTION Technical data To gain the best performance of Power requirements the tool, prolong the duty life, make the Warranty valid if General power tool safety warnings necessary, and to avoid hazards of fatal injuries please read and Safety warnings for the use of plasma understand this Manual before cutters using the tool.
- Página 3 Technical specifications COPLA-60X Code 17332 Description Plasma Cutter INPUT Voltage 220 V Frequency 60 Hz Current 49 A OUTPUT Open Circuit Voltage 305 V c.c. Current Range 20 A - 60 A Maximum Cutting Capacity 1” Ideal Cutting Capacity 3/4”...
- Página 4 General Power Tools Safety Warnings WARNING! Read carefully all safety warnings and instructions listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.
- Página 5 Safety Warnings for Plasma cutter Protection Equipment To Prevent Fire CAUTION • Wear a welder helmet to protect your • Always have a fire extinguisher handy. WARNING eyes and face when working with the equipment. Assure WARNING • There shall be no flammable or the helmet shadow lens is the right one for the cutting process explosive material in the work area (not less than 36 ft away).
- Página 6 Parts Fast Connection Intake Pressure Clamp to Regulator ground the work piece Carrying Handle switch Cutting Current Indicator Activated Thermal Power Protection Indicator Indicator Air Low Gauge Level Rotameter Indicator Current Control Clamp Terminal Ventilation Slots Torch Line Terminal Current Connectors Electrode Wrench...
- Página 7 Installation Torch CAUTION Make sure the torch is correctly assembled before connecting into the equipment. • Assemble all the torch parts in the same order as shown in the graph. • When it is assembled connect the torch to the front panel terminal (A).
- Página 8 Start Up Air pressure adjustment CAUTION • Double check the plasma cutter is connected right in good working conditions as described in page 7. Make sure you follow the safety Warnings in pages 4 and 5. • Turn ON the cutter switch (A) to see if the operation is normal. If so, the fan will start and the power indicating light will be ON (B).
- Página 9 Start Up Pilot Flame General Considerations 1. Upon pressing and releasing the torch trigger, air will • The cut shall always start in the work piece edge. Move start coming out without generating any arc. the torch in one direction only unless piercing is required. 2.
- Página 10 Start Up • When pushing the trigger both current and compressed air reach the torch head where air changes status, from gas to plasma when interacting with the electric arc. • The cut starts when the plasma is driven out through the torch nozzle attracted by the work piece grounded with the clamp.
- Página 11 Maintenance • Proper use and regular cleansing lengthen the useful life of the plasma cutter. CAUTION • Only certified personnel shall carry out repairs. We recommend visiting a Authorized Service Center to repair the plasma cutter and purchase supplies or accessories. Regular Maintenance Storage •...
- Página 12 Troubleshooting Problem Cause Solution The power indicating • Input voltage is not 220 V • Connect the supply cable into a 220 V outlet. light is not ON after • The light is not working . • Go to a Authorized Service Center turning ON the to repair.
- Página 13 Authorized Service Centers In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800-018-7873 to get information about the nearest Service Center. AGUASCALIENTES DE TODO PARA LA CONSTRUCCIÓN MORELOS...
- Página 14 Model Brand 17332 COPLA-60X Warranty. Duration: 5 year. Coverage: parts, components and workmanship against manufacturing or operating defects, except if used under conditions other than normal; when it was not operated in accordance with the instructive; was altered or repaired by personnel not authorized by Truper .