Publicidad
Idiomas disponibles
Idiomas disponibles
Remote Control Features and Settings
10. HEALTH AIRFLOW (Only available for some particular model):
Health Airflow function will stir the air in the room
(1) Press the HEALTH AIRFLOW button to show
display.
(2) The Quadrant icon will cycle to each quadrant.
(3) Horizontal swing default is oscillate. It can be adjusted with
each press of the Horizontal SWING Button between narrow,
mid, wide and left to right.
(4) Vertical swing is not adjustable.
(5) Fan speed default is variable. It can be adjusted by pressing
FAN SPEED Button between low, medium and high.
11. Sleep Orperation Mode:
(1) SLEEP mode during COOL, DRY modes
One hour after SLEEP mode starts, the temperature will rise
2°F above set temperature, after another hour, the temperature
rises an additional 2°F. The unit will run for an additional six
hours, then turns off. The final temperature is 4°F higher than
the initial set temperature. Using this feature will help with
achieving maximum efficiency and comfort from your unit while
you sleep.
(2) SLEEP mode during HEAT mode
One hour after SLEEP mode starts, the temperature will
decrease 4°F below set temperature, after another hour, the
temperature will decrease an additional 4°F. After an additional
three hours, the temperature will rise by 2°F. The unit will run for
an additional three hours, then turns off. The final temperature
is 6°F lower than the initial set temperature. Using this feature
will help with achieving maximum efficiency and comfort from
your unit while you sleep.
(3) In SMART Mode
The unit operates in corresponding sleep mode adapted to the
automatically selected operation mode.
NOTE: When the TIMER ON function is set, the sleeping
function cannot be set. If the sleeping function has been set,
and the user sets the TIMER ON function, the sleeping function
will be canceled, and the unit will be set to the timer function.
12. HEALTH (Only available for some particular model):
(1) During power-on or power-OFF, press HEALTH button to
display icon
on LCD display, and press HEALTH button again
to cancel.
(2) During power-OFF, press HEALTH button to enter Fan mode,
start low wind and HEALTH function, display icon
(3) Switch among modes, and keep HEALTH function.
(4) If HEALTH function is set, power OFF and then on to stay in
HEALTH mode.
(5) HEALTH function is not available for some units.
13. ECO:
(1) Press ECO button and the display will show
(2) ECO is valid under all modes, it is memorized among switch
of all modes.
(3) ECO function power-on or power-OFF is memorized.
(4)ECO function is not available for some units.
14. Turbo/Quiet:
The TURBO function is used for fast heating or cooling. Press
TURBO button, the remote control will display the TURBO and
switch the fan to SUPER high. Press TURBO button again to
cancel function.
Press QUIET button, the remote control will display the QUIET
and switch fan to BREEZE. Press QUIET button again to cancel
function.
NOTE: TURBO/QUIET modes are only available when the unit is
under cooling or heating mode (not for smart or dry mode).
6
Running the unit in QUIET mode for a long period of time may
cause the room temperature to not reach the set temperature. If
icon on LCD
this occurs, cancel QUIET mode and set the fan speed to a higher
setting.
15. Requires optional motion sensor part (Only available for some
particular model):
Smart Focal Point (iFP) will operate the unit at set point only
when the room is occupied.
16. Evade/Follow (Only available for some particular model):
When the iFP sensor is installed the airflow can be set to follow
occupants or evade them.
17. FRESH (Only available for some particular model):
(1) FRESH function is valid under the state of ON or OFF. When
air conditioner is OFF, press FRESH button, display icon
LCD display to enter Fan mode and low speed. Press FRESH
button again, this function is cancelled.
(2) After FRESH function is set, ON or OFF functions are kept.
(3) After FRESH function is set, mode switch function is kept.
(4) FRESH function is not available for some units.
18. °C/°F Function:
Press MENU/°F to toggle between [set temp]°F; [set temp]°C;
and 10°C/50°F Low Temperature Heating mode. Low
Temperature Heating is only available when set to HEAT. When
set to Low Temperature Heating, the set point is dropped to
a minimum temperature to prevent damage from freezing
temperatures.
.
8
7
11
14
19
20
22
23
9
17
12
18
21
25
27
24
26
on
10
49-5000513 Rev. 1
Publicidad
