Publicidad
Idiomas disponibles
Idiomas disponibles
ENgLISh
3. Plug the USB plug
11
computer or wall adapter). The green charging LED
will continuously blink while charging.
4. Charging is complete when the green charging LED
remains continuously ON. Battery can be left charging or
USB cable can be disconnnected.
Hot/Cold Delay
When the tool detects that the battery is too hot or too cold,
it automatically starts a hot/cold delay, suspending charging
until the battery has reached an appropriate temperature.
The tool then automatically switches to charging mode. This
feature ensures maximum battery life.
1. A cold battery may charge at a slower rate than a
warm battery.
2. The hot/cold delay will be indicated by the green
charging LED
8
remaining OFF.
3. Once the battery has reached an appropriate
temperature, the green charging LED
blink, indicating that the tool has resumed the
charging procedure.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery will need to be recharged.
Important Charging Notes
1. The tool may become warm to the touch while charging.
This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the tool after use,
avoid placing the tool in a warm environment such as in
a metal shed or an uninsulated trailer.
2. If the tool does not charge properly, take the tool and
USB cable to your local service center.
3. You may charge a partially used battery whenever you
desire with no adverse effect on the tool.
USB‑C Power Port (Fig. B)
The USB symbol on the USB-C charging port cover
indicates that this tool is equiped with a USB-C style
charging port.
State of Charge Indications (Fig. A, D)
Each time the forward
2
the charging LED
8
will illuminate for five seconds to
indicate the approximate level of charge remaining
according to the following:
gREEN 75-100% charge
YELLOW 15-74% charge
RED < 15% charge
Flashing RED
or no illumination
6
into any USB port (such as on a
8
will continuously
7
or reverse button
3
is pressed
Low battery. Tool will need to
be recharged.
ASSEMBLY AND ADJUSTMENTS
8
WARNING: To reduce the risk of serious personal
injury, make sure the forward/reverse button is in the
8
center, locked position while making any adjustments
or removing/installing attachments or accessories. An
accidental start‑up can cause injury.
OPERATION
WARNING: To reduce the risk of serious personal
injury, keep away from the forward and reverse
buttons while making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
WARNING: Potential electrical shock risk. Ensure
USB‑C charging port cover
avoid potential shock if live wire is touched. Tool is not
electrically insulated.
Inserting and Removing Bits (Fig. E)
NOTE: The quick-release chuck
accessories only.
To install a bit
13
backward and insert the bit into the quick-release chuck
Release the quick-release chuck sleeve
into place.
To remove a bit, pull and hold the quick-release chuck
sleeve
5
backward. Remove the bit
quick-release chuck sleeve
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
1
.
LED Worklight (Fig. A, C)
CAUTION: When using the worklight for purposes
other than screwdriving or drilling be sure to
remove all accessories. Unused accessories could
cause injury or property damage.
CAUTION: Do not stare into the LED. Serious eye
injury could result.
When the screwdriver is activated by pressing the forward
or reverse button
turn on. The LED worklight will turn off ten seconds after the
forward
2
or reverse button
Performing an Application (Fig. A, F)
WARNING: Do not strike the screwdriver or use as a
chisel or pry bar in any position.
WARNING: To avoid the screwdriver being turned on
accidentally, do not carry in your pocket.
Insert the appropriate hex shank bit into the
quick-release chuck
7
is closed prior to use to
6
accepts 1/4" (6 mm) hex
, pull the quick-release chuck sleeve
5
to lock the bit
13
and release the
5
.
3
, the LED worklight
4
will automatically
3
has been released.
6
.
5
6
.
2
Publicidad
