Master ARCO Serie Manual De Usuario página 2

ARCO series
User manual for
Dear Customer, thank you for purchasing a MASTER
S.p.A. product. This guide contains all the information you
will need concerning the use of this product. Read the
instructions carefully and keep them for further
consultation.
ARCO is designed specifically to control sun awnings,
blinds, roller shutters, screens or similar items. All other
use beyond the field defined by MASTER S.p.A. is
forbidden. This, as well as the breach of the instructions
given in this guide, shall release MASTER S.p.A. from any
liability and shall annul the product warranty. Water,
humidity, heat sources, accidental falls can damage the
device. Do not use abrasive products or solvents to clean
the product.
All products and technical specifications given in this document
are subject to variation without notice. Unless previously and
specifically authorised by the manufacturer, the device must be
used exclusively with receivers produced by the same
manufacturer. The manufacturer shall not be liable for damage
resulting from improper, incorrect or unreasonable use.
Notes on radio system
The radio range is limited by radio appliance control
standards. Do not use radio systems in places with strong
interference (for example, near police stations, airports,
banks, etc). It is iadvisable to carry out a technical inspection
prior to installing a radio system in order to identify possible
sources of interference. Radio systems can be used where
any disturbances or malfunction of the transmitter or receiver
do not constitute a risk factor, or if such factor is eliminated
using appropriate safety systems.The presence of radio
devices working at the same transmission frequency may
reduce the range of the system, limiting functionality.
Disposal
At the end of the product life cycle, dispose of the
device in compliance with local regulations. This
product could contain substances that are harmful to
human health and the environment: do not dispose
of the product in domestic waste.
rev04_02.08.22
www.mastermotion.eu
MASTER S.p.A. via Pertini 3, 30030 Martellago (VE)
fig.1
fig.2
fig.3
MENU
4 DELAY OF TRANSMISSION ON GROUPS AND SEQUENCER CHANNEL
For Sequencer channel and for the Groups you can set the interval of time (from 1 to 10 sec) which must pass between the transmission on one channel and the next. The factory sets the
delay at 1 second. The use of high intervals of time can negatively effect on the battery life. To modify the setting:
A) Press togheter STOP and MENU
B) Press NEXT . The Sd symbol appears on the display.
C) Press STOP . The currently set value appears on the display (from 01 to 10 sec).
D) Use PREV and NEXT to set the required value.
E) Press STOP to save the setting.
F) To exit, press 1 time MENU or wait about 15 seconds (the display switches off).
NOTE! ARCO series can be used with different types of receivers (motor, control unit, etc.): the first memorization
R
procedure, the procedure for memorizing additional remote controls (in addition to the first one) and the various
433,42 MHz
procedures for changing the settings of the receivers are listed in the manuals of the various devices.
Technical specifications
- Power supply:
- Operating temperature:
- Operating frequency:
- Operating frequency band:
- Max radiated power, e.r.p. :
SEQUENCER: ARCO 2 ARCO 5
GROUPS: ARCO 20
Fixing the wall bracket
A) Fix (at a height of less than 2m) the bracket to the wall using the supplied plugs (see fig.1).
B) Cover the screw heads with the coverage provided.
C) Hang the transmitter to the support.
Battery insertion/replacement
The transmitter is powered by a battery CR2032. To insert the battery: remove the battery cover on the back of the
transmitter, insert the battery respecting the polarity, close the cover (see fig.2). Used batteries must be discarded in
appropriate containers. It it recommended to replace the battery every 2 years.
1 FUNCTIONS ASSOCIATED WITH THE TRANSMITTER BUTTONS
NOTE: It is possible that some receiving devices do not associate any operations to some transmitter buttons or that
associate to the transmitter buttons some operations different from what it is described. In this case consider the
instruction manual of the receiving device.
To memorize:
36mm
Press togheter STOP and FOR ME and hold
the buttons until the receiver signalation (about 5 seconds)
By the «SUN On / Off " button you can activate / deactivate the SUN function or the AUTOMATIC LOWERING function, in
the receivers equipped with these functions. To modify the setting:
A) Select the channel (excluded sequencer channel and groups)
B) Press
C) If YELLOW LED IS ON
NOTE: In ARCO2 the «
automatically activated for channel 2 and viceversa
2 ENABLING/DISABLING GROUPS AND CHANNELS
With transmitters
same procedure, reactivate the channels. The procedure is as follows:
A) Press togheter
B) Press
C) If YELLOW LED IS ON channel/group enabled
D) Press
E) If necessary,press PREV and NEXT to select another channel/group and return to point C.
F) To exit,
SETTING THE CHANNELS BELONGING TO A GROUP (only ARCO20)
3
To configure the different groups, selecting which channels should be part of them, follow the procedure below:
A) Press togheter
PROG B) Press twice NEXT.
C) Press STOP. Channel 01 appears.
D) If YELLOW LED IS ON: channel belongs to the group
If RED LED IS ON channel not belongs to the group
E) Press
F) If necessary, press PREV and NEXT to select another channel and return to point E.
G) To exit,
and hold the buttons for about 3 seconds, until the
n° 1 CR2032 lithium battery
0° C - +55°C
433.42 Mhz
433,050 – 434,790 Mhz
, and ARCO 10
succession (see also paragraph 4), for all active radio channels, the selected command. To select the
Sequencer, scroll through the list of channels until the
is equipped with 4 virtual channels called
succession (see also paragraph 4), for all the active radio channels belonging to the group, the selected
command. To select a group, scroll through the list of channels until the symbols G1, G2, G3 and G4 appear.
Up to 20 channels can be associated with each group.
Do not ingest the battery, chemical burn hazard
This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause
severe internal burns in as little as 2 hours and lead to death.
Keep new and used batteries out of the reach of children. If the battery compartment does not close tightly,
discontinue use of the product and keep it out of the reach of children. If you suspect batteries have been
swallowed or inserted into other body orifices, seek immediate medical attention.
Risk of explosion if battery is replaced with wrong type. If the battery is subjected to high temperatures (fire,
hot oven), if it is crushed or cut, there is a risk of explosion and leakage of flammable liquids or gases. Do not
recharge non-rechargeable batteries.
channel -/+
up
prev/next
stop
right orientation
down
left orientation
FAVORITE POSITION
SUN / AUTOMATIC LOWERING FUNCTION
until the state of the yellow LED varies (about 2seconds)
: sun/automatic lowering function
Sun/Automatic lowering»
ARCO 5 ARCO 10 , and ARCO 20
STOP and MENU and hold the buttons for about 3 seconds, until the
STOP 01 . will appear.
:
STOP to modify the setting.
press twice MENU or wait about 15 seconds (the display switches off).
STOP and MENU and hold the buttons for about 3 seconds, until the
G1 symbol appears on the display. To select another group press NEXT.
:
STOP to modify the setting.
press twice MENU or wait about 15 seconds (the display switches off).
ch symbol is displayed.
- N° of channel ARCO:
- N° of channels ARCO2:
- N° of channels ARCO5:
- N° of channels ARCO10: 10 + sequencer channel
<10 mW - N° of channels ARCO20: 20 + 4 groups
are equipped with a virtual channel called
SE symbol appears.
Groups (indicated with
WARNING
BASIC FUNCTIONS
SUN On/Off
FOR ME
To recall:
active
function is active for both channels: if you enable it for channel 1, it is
you can turn off the channels that are not used; it's possible, with the
/ If RED LED IS ON channel/group disabled :
1
2 + sequencer channel
5 + sequencer channel
Sequencer : it sends in
G1 G2 G3 G4 , , , ) which send in
access to the
MENU
receiver menu (see fig.3)
transmitters
PROG
insertion-deletion (see fig.3)
RED Led YELLOW Led
ch symbol is displayed.
ch symbol is displayed.